Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

VHF/UHF antenna choices: J-pole vs collinear vs yagi, mobile mounts, coax and connectors, and what SWR does and doesn't tell you

ci_cover.jpg

Let's pull together the practical trade-offs for VHF/UHF antennas in one place. The same questions keep coming up: which antenna type for which job, how much gain is real, and why a good SWR reading doesn't always mean a good signal. Here is a framework to argue with.

Start with the job, not the antenna. A repeater user on 2 m/70 cm FM wants vertical polarization and a pattern that is round in azimuth. A weak-signal SSB/CW operator on 2 m, 70 cm or higher normally wants horizontal polarization and a directional beam. A LEO satellite operator needs something that copes with a moving target and changing polarization. Gain only helps if the pattern points where the signal is.

Quarter-wave and 5/8 wave whips. A quarter-wave is about 234/f(MHz) feet, minus a little for the velocity factor of the element. That is roughly 19 inches on 2 m and just over 6 inches on 70 cm. It needs a ground plane, such as a car roof, to act as the other half of the antenna. A 5/8 wave whip is taller, usually has a matching coil at the base, and puts more energy toward the horizon. The usual figure is a couple of dB over a quarter-wave. The real number depends on the ground plane and on how honest the manufacturer is, so treat catalog gain as best case. A 5/8 wave on a small or off-center ground plane can show a decent SWR and still radiate with a skewed pattern.

J-pole and Slim Jim. Both are end-fed half-wave antennas with a quarter-wave matching section. The J-pole is simple, cheap to build from copper pipe or twin-lead, and needs no radials in principle. In practice the coax shield can carry common-mode current and become part of the antenna, which distorts the pattern and moves the SWR depending on how the cable is routed. A choke of a few turns of coax or ferrite beads near the feedpoint often helps. The Slim Jim is a folded variant with a lower radiation angle, which can help on flat-terrain simplex or repeater work. As with any homebrew, accuracy of dimensions and a clean feedpoint matter more than the design name.

Collinears. Stacking phased half-wave sections flattens the elevation pattern. That concentrates energy toward the horizon, which is what you want for a base station or repeater in open terrain. The catch is that more gain means a narrower vertical beam. On a mast in hilly terrain, or when you're talking to stations well above or below you, a high-gain collinear can be worse than a modest antenna. Mounting also matters. A collinear beside a metal mast will have its pattern pulled off-center unless it is mounted with enough standoff or on top of the mast.

Yagis. A yagi trades coverage for gain and front-to-back ratio. Polarization needs to match: crossing vertical and horizontal polarization can cost on the order of 20 dB in practice, though reflections and ground effects vary it. Most FM repeater and simplex work uses vertical, and SSB/CW weak-signal work conventionally uses horizontal, so check local band-plan practice before committing to a mast orientation. For FM satellites, hand-held three-element yagis can work well because you can point them by hand and rotate them to find the best polarization. Crossed yagis with circular polarization (or switchable RHCP/LHCP) reduce fading from rotation of the satellite, at the cost of a more complex feed and phasing harness.

Mobile mounts. NMO needs a 3/4 inch hole but gives a solid, low-loss mechanical and electrical connection to the roof. It is the usual choice for permanent installs. A magnetic mount is quick to fit, but the coupling is partly capacitive through the paint, so the antenna can detune, and a dirty or scratched surface may degrade performance. Place the antenna at the center of the roof if you can. Running the coax through a door gasket can damage the cable or the weather seal, so a flat-profile cable or a route through a rubber grommet is neater.

Coax and connectors. PL-259 (UHF connectors) are common and fine for HF and often acceptable on 2 m. They are not constant-impedance and are not weatherproof, so loss and mismatch get worse by 440 MHz and above. N-type connectors are constant-impedance, weatherproof when properly sealed, and are the better choice for 70 cm and up. Cable loss climbs quickly with frequency. Approximate numbers: RG-58 loses roughly 5 to 6 dB per 100 ft at 150 MHz and 10 dB or more at 450 MHz, so keep it short. Low-loss types like LMR-400 or similar can be around 1.5 dB per 100 ft at 150 MHz and under 3 dB at 450 MHz. Check the datasheet for your exact cable.

SWR. SWR measures how well the antenna and feedline match the transmitter's impedance. It isn't a measure of efficiency or gain. A dummy load has a perfect SWR and radiates nothing. Lossy coax can also make the SWR look better at the radio than it really is at the antenna, because power lost in the cable on its way to and from the mismatch reduces the reflection that you see. For a fair test, measure at the antenna end if possible, away from metal clutter, with the antenna in the position it will be used in.

Repeater and satellite antennas. A repeater system with a shared antenna needs a duplexer to keep transmit energy out of the receiver. If separate antennas are used, vertical separation is more effective than horizontal separation for isolation. For satellite work, the key practical points are pointing accuracy, polarization, and Doppler shift, which will move the received frequency noticeably on 70 cm during a pass.

So what's your use case, and which of these compromises do you find hardest to make? Share the band, the terrain, and whether you're on a rooftop, mast, or vehicle, and we can narrow things down.

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One point on the J-pole: the feedline is a bigger factor than most descriptions admit. If it drops straight down alongside the pole, it can radiate and take the pattern with it. A common remedy is to run the coax away from the antenna at a right angle for a few feet and add a choke at the feedpoint. Also watch the matching point. The tap position is sensitive, so adjust it with the antenna in its final location, not on the bench, because nearby metal and the mast change the match.

For the mobile discussion, a 5/8 wave isn't automatically better than a quarter-wave. On a small roof, or off to one side on a trunk lid, the quarter-wave is often the safer choice because it is less sensitive to ground plane size. The 5/8 starts to make sense when you have a decent metal surface under it.

  • Moderators

On connectors, I'd treat N-type as the default for anything permanent outdoors on UHF. A PL-259 with a cheap solder job and no sealing is a common point of water ingress, and the coax can end up with a green, corroded braid after a season or two. Whichever connector you use, wrap it with self-amalgamating tape, then add a layer of vinyl tape over it for UV protection, and leave a drip loop in the cable before it enters the building.

Regarding satellites, if you're just starting with FM LEO passes, a handheld dual-band yagi and an HT with full-duplex capability (or two radios) is an easy way in. The detail people miss is that polarization shifts during a pass as the satellite tumbles or you change angle, so rotating the yagi around its boom axis can bring a weak signal back up. Crossed elements and circular polarization are nice upgrades, but not required to make a first contact.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.