Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting started with LEO satellite work: FM birds, linear transponders, Doppler and tracking setup

ci_cover.jpg

I'd like to collect the practical points of working amateur satellites in one thread. The topic covers a lot: FM "easy sats" like SO-50, AO-91 and AO-92, the ISS APRS digipeater and crossband voice repeater, SSB/CW linear birds like RS-44, and the geostationary QO-100. Each one asks for a different mix of antenna, radio and operating habit.

Start with the two main categories. FM satellites are single-channel repeaters in space. You transmit on one frequency, the satellite retransmits on another, and everyone on the pass shares that one channel. It behaves like a very fast, very busy repeater, so short exchanges work best: callsign and Maidenhead grid square, such as "W1XYZ FN42", and that's it. Many FM birds need a CTCSS tone on the uplink. SO-50, for example, has historically needed an arming tone before the 67.0 Hz access tone. Frequencies, tones and operational status change, so check a current satellite status page or the AMSAT site before a pass rather than trusting a list in a forum post.

Linear transponders such as RS-44 translate a whole slice of spectrum rather than one channel. Many stations can operate at once on SSB or CW, and you find yourself in the passband and tune around like on HF. RS-44's transponder is inverting, meaning that if you raise your uplink frequency, the downlink moves down. Many operators tune the downlink to hear themselves on a stable frequency and adjust the uplink to compensate for Doppler. Software can take care of that for you.

Speaking of Doppler: the shift comes from the satellite's radial velocity relative to you. As a rough guide, on 70 cm it can reach about ±10 kHz over a low-orbit pass, and about a third of that on 2 m. It's largest on approach and recession, and it passes through zero at closest approach. On FM, with its 15 to 25 kHz channel width, you'll need to retune in steps during the pass, particularly on the 70 cm side. On SSB or CW it matters much more, since a few hundred hertz of error turns a voice into Donald Duck.

For software, Gpredict (free, cross-platform) gives you pass predictions, a map, and rig and rotator control through Hamlib's rigctld and rotctld. SatPC32 is a Windows program that is well established for Doppler and CAT control of many radios. Both need up-to-date Keplerian elements (TLEs). Stale elements are a classic reason a "perfect" pass looks off by a few degrees or a few seconds.

On the antenna side, the usual starting point is a handheld dual-band Yagi such as an Arrow-style antenna, with a duplexer if you're using one feed line. You aim by hand and use a pair of radios or a single full-duplex radio so you can hear your own downlink. Beyond that, a pair of crossed Yagis on an az/el rotator gives a steadier signal and frees your hands for the logbook. Circular polarization is common, though a linear antenna works fine for many casual passes. Remember that elevation matters on a good overhead pass, so an azimuth-only rotator tracks poorly then.

Finally, QO-100 stands apart. It's a geostationary satellite, so there's no Doppler and no pass prediction. You point a dish once and it stays aimed. The trade-off is a 2.4 GHz uplink, a 10 GHz downlink, and some stability and pointing demands of its own. Coverage is regional rather than global, so check the footprint for your area.

So where do you want to dig in: antenna choices for FM, the tuning routine on RS-44, or the automation setup in Gpredict and SatPC32?

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One thing that helps with FM passes is to prepare before AOS rather than during it. Check the current uplink frequency and CTCSS tone for the bird, set up your memories (downlink with and without Doppler offsets, if your radio allows it), and look at the max elevation in your tracking program. A pass peaking at 15 degrees is a different proposition from one at 70 degrees. Low passes mean a short window and more noise, and you're often better off waiting for a better one while you practise.

With a handheld Yagi, a common mistake is holding the antenna in the wrong plane or flexing the coax and moving the antenna around. Keep the boom pointed at the predicted position, and let the radio's S-meter help you peak it. Also, listen first. Hearing how other stations make short exchanges and how they handle contention will save you a lot of unanswered calls.

On the ISS, it helps to know which function is active on a given day: the APRS digipeater and the crossband repeater generally aren't both in use at once, and operations vary. Check the status before assuming silence means your station is deaf.

  • Administrators

For SSB or CW on RS-44, the point that's easy to miss is that a linear transponder is about your downlink as much as your uplink. A practical method is to listen to the transponder's passband first, find a clear spot, and then set your transmit frequency so the return lands where you want it. With an inverting transponder, you move the uplink opposite to the Doppler direction. Many people let Gpredict or SatPC32 handle this through CAT control, with a manual offset you can nudge to place your signal. If your radio is slow to respond to frequency commands, check the update interval and avoid bandwidth-hungry polling that makes the display jump.

Power matters less than you think. A satellite downlink that is much louder than the others usually means someone is running too much power and pushing the transponder, so keep your signal about as strong as the beacon. If you hear yourself at about the same level as the beacon, that's a good target. Start low and increase only if you really can't hear your return.

For CW the advantage is clear: a narrow signal punches through at low power, and the Doppler tolerance is more forgiving if you aren't chasing a precise zero-beat. For SSB, expect to retune the uplink repeatedly, or let the software do it. Either way, take the time to confirm that your computer clock and TLEs are current before the first pass.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.