Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead or half-dead rig: a triage order for no TX, no RX, SWR foldback and noise

ci_cover.jpg

Most "dead rig" problems get easier once you stop treating them as one big mystery and work in a fixed order. This is a sequence for bench-diagnosing an HF or VHF transceiver, with notes on where each fault type usually hides. Corrections and additions are welcome.

1. Power first, and measure it under load. A supply that reads 13.8 V with nothing connected tells you very little. Measure at the rig's DC input terminals while the rig is receiving, and again while transmitting into a dummy load. A few tenths of a volt of drop across a fuse holder, an Anderson connector or a thin lead is common. Many rigs will reset, drop power or fold back when the supply sags on transmit peaks. Check the fuse in the rig's DC lead and the reverse-polarity protection. If the supply is a switcher, look at its output with a scope for ripple and spikes, since a failing switcher often looks fine on a DMM. If you can, bring the rig up on a current-limited bench supply the first time, or put a series lamp in the positive lead on tube or older solid-state gear. A shorted final or regulator will show itself without taking anything else with it.

2. No receive. Rule out the obvious controls first: AF gain, RF gain, squelch, attenuator and preamp state, mode, and the noise blanker. Then work out whether the problem is audio, signal path or oscillators. Touching the volume control or the speaker line with a screwdriver tip and hearing a buzz tells you the audio stage is alive. A tone or modulated signal injected at progressively earlier stages (audio, detector, IF, mixer, front end) will show you where the signal disappears. If the synthesizer or PLL isn't locking, you can get a rig that powers up and looks normal but hears nothing, so check the reference oscillator and the PLL lock voltage if the manual gives one. Also check the antenna relay and the receive path through it. A relay that doesn't drop out, or one with oxidised contacts, can leave the receiver effectively disconnected.

3. No transmit. Split it into three questions. Does PTT actually change state (relay click, TX indicator, bias switching)? Is there drive from the exciter to the driver stage? Is there output from the final? Always use a dummy load and a power meter, and never test with the antenna port open. Without drive you suspect the mic or PTT line, ALC, or the exciter. With drive but no output you look at bias, the driver, the final, and the output filter relays. A DMM on the bias line and on the collector or drain current while keying shows a lot.

4. SWR protection faults. If the rig folds back on a known-good dummy load, the antenna and coax aren't the problem. Suspect the detector instead: the directional coupler, the rectifier diodes, the reflected-power trimmer, and the connections to the board. Compare forward and reflected sample voltages against the manual. If reflected voltage is present into a good load, the bridge or its balance adjustment is the likely fault. If protection trips only on the antenna, check the coax, connectors, tuner and any antenna switch, and put a separate SWR meter in line.

5. Blown finals: find out why before replacing them. Final transistors usually die for a reason, such as high SWR with weak protection, bias runaway from a failed bias regulator or thermistor, parasitic oscillation, an overvoltage event, or poor heat sink contact. Replacing the device alone often means it fails again. Check the bias network, driver stage and protection components, replace with the correct or properly matched parts, and use fresh thermal compound. Set the idle current to the service manual value on a current-limited supply with a dummy load, and bring up power gradually.

6. Capacitors. Aged electrolytics in power supply sections, audio stages and decoupling are a frequent cause of hum, noise, instability and odd resets. They are worth testing with an ESR meter or checking visually for bulging and leakage, particularly in older gear. Replace with the same capacitance, at least the same voltage rating, and the correct type (low-ESR where the original was). Watch polarity. Don't casually swap mica, ceramic or trimmer capacitors in RF and filter sections for a different type, since that changes the circuit's behaviour. Clean electrolyte residue off the board with isopropyl alcohol, as it can corrode traces. Blanket recapping without measuring first can add risk without fixing anything.

7. Contacts and connectors. Intermittent faults, scratchy controls, and mode or band problems are often contact issues. Clean switches, relays, board-to-board connectors and pots with an appropriate contact cleaner or isopropyl alcohol, and reseat connectors. Check for cold or cracked solder joints around heavy components, connectors and anything that flexes or heats up.

8. Noise. Separate noise that comes in via the antenna from noise generated inside the rig or on its power. Disconnect the antenna and terminate the input. If the noise stays, it's internal or on the supply. Swap in a clean linear supply or battery. A switching supply, a bad regulator, failing capacitors or a poor ground can all inject noise. If it disappears when the antenna is disconnected, it's external: look at the feedline, common-mode currents and local interference sources.

9. Alignment comes last. Alignment can't cure a failed part, and tweaking slugs and trimmers on a faulty rig often makes things worse. Fix the fault, then follow the service manual procedure with the equipment it specifies (a calibrated signal generator, a frequency counter, a dummy load and an RF wattmeter). Mark or note the starting positions before touching anything.

Service manuals and test gear. A service manual gives you the block diagram, test points, expected voltages and alignment steps, and these often shorten the job a lot. A DMM covers DC voltage, current and resistance. A scope shows ripple, audio waveforms, oscillator presence and RF envelope. Use a proper probe with a short ground spring on RF, and remember that a standard DMM isn't an RF voltmeter. An RF probe or a dedicated RF meter is the right tool for RF levels. Be careful with line-powered equipment and scope grounds, and treat tube gear and high-voltage supplies with full respect.

What order do you use when a rig arrives with a vague complaint? And what checks do you do before opening the case at all?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

The dummy-load test for SWR foldback is the one to do early, because it separates "the rig is unhappy" from "the antenna system is unhappy" in about a minute. If it still protects on a known-good load, I'd go straight to the sensing circuit: the bridge diodes, the trimmer and any cold joints on the coupler board. If the rig reports high SWR on a dummy load, it's worth putting an external meter in line to see whether the rig's reading is real before assuming a detector fault.

One more thing on finals: check whether the protection circuit works at all before putting the rig back in service. If a rig blew a final because foldback never kicked in, the sensing or ALC path may be the real fault, and the new transistor just becomes the next casualty.

  • Moderators

Agree on measuring supply voltage at the rig under TX load. A lot of "no transmit" or "resets on SSB peaks" complaints come down to voltage drop in the DC lead, a tired fuse holder or a supply that can't hold up on peaks. A scope on the supply rail while keying will show it straight away.

On capacitors, I'd measure before replacing. An ESR meter or a scope looking at ripple on the rail tells you which ones are actually bad. Replacing everything on a hunch can introduce new problems, like a reversed polarity cap, a damaged pad or a wrong-value part in a timing or filter circuit. Targeted replacement of the ones that fail the test is usually safer, and you keep a record of what changed.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.