Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dual-band mobile setup: FTM-500D vs ID-5100A vs TM-D710G, plus wiring, noise and etiquette

ci_cover.jpg

I'm starting a general thread for people planning or fixing a 2 meter / 70 centimeter mobile install. The three radios that come up most for a new dual-band mobile are the Yaesu FTM-500D, the Icom ID-5100A and the Kenwood TM-D710G. All three are roughly 50 watt class FM radios with dual receive, but they differ in digital modes, display style and extra features. Check each manufacturer's current specs and manual before buying, because features vary by model and firmware.

The rough split: the FTM-500D is a Yaesu System Fusion (C4FM) radio, the ID-5100A is a D-STAR radio with a touchscreen, and the TM-D710G is a Kenwood with a built-in APRS TNC and a reputation for flexible data features. If your local repeaters are mostly analog FM, any of them will do the job. If your area leans toward one digital mode, let that choose the radio.

Some questions to get things going:

  • Cross-band repeat: Is it worth having in a mobile? The usual use is a vehicle-based repeater for a handheld when you are away from the vehicle. I would not assume every radio above supports it, so check the manual and menu for the exact model before relying on it. Also keep in mind that licensing rules and ID requirements still apply when you retransmit.
  • Mounting: Where does the control head or main body go so it is reachable but does not interfere with airbags, seat travel or your sightlines?
  • Power wiring: Direct to the battery with a fuse near the positive terminal, or a switched fused distribution block?
  • Noise: What do people do about alternator whine, ignition noise and hash from LED lighting or aftermarket electronics?
  • Etiquette: What are the unwritten rules for mobile operation on busy repeaters and simplex calling frequencies?

I'd like this thread to collect practical, model-neutral advice that a first-time installer can follow, with room to disagree where practices differ.

  • Replies 2
  • Views 34
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On power, the main idea is to protect the wire, not just the radio. A fuse on the positive lead as close to the battery terminal as practical protects the cable run if it shorts to the body or gets chafed. The radio's own inline fuses are a second layer and do not replace that one. Use the cable the radio comes with and keep it as short as you can. If you must extend it, use heavier wire than the original and make the splice with proper crimps or solder and heat shrink, not twist-and-tape.

Don't power a 50 watt radio from a cigarette lighter socket unless the manual explicitly allows it. Those circuits are often thinly wired and share fusing with other devices, and the voltage drop on transmit can cause weak audio or resets. When you go through the firewall, use an existing grommet or add one, so the insulation is not cut by a sharp edge. Route the negative to a solid, clean chassis point or straight to the battery negative, whichever you can do cleanly and safely.

For mounting, the common mistakes are blocking airbag deployment zones and putting the main body where it traps heat. Leave airflow around the heat sink and check that the mic cable cannot snag on the gear shift or seat adjuster. Dual-band radios with a detachable control head are easier to fit in a modern dash, but the extra cable needs tidy routing too.

  • Moderators

For noise, work out where it is coming from before buying anything. Turn the radio on with the engine off, then start the engine, then rev it, then switch accessories on one at a time. A whine that follows engine RPM usually points to the alternator or to power wiring picking up noise. A ticking sound that follows the engine usually points to ignition. A steady hash that appears when you turn something on, like a dash camera, LED lights or a USB charger, is probably switching supply noise from that accessory.

Common fixes are keeping the radio's power leads away from the vehicle's harness, moving to a better ground, and trying a ferrite on a suspect accessory's power lead. It also helps to keep coax well away from power cables. Antenna placement matters as well. A roof or trunk-lid NMO mount over good metal gives a better ground plane than a mag mount on a hatch or a lip mount that depends on a weak bond. Check SWR on both 2 meters and 70 centimeters, since a dual-band antenna can be good on one band and mediocre on the other.

For etiquette, keep it short and sensible. Listen first, identify as the rules require, and don't hold up a repeater with long transmissions while driving. If traffic demands your attention, stop talking. Use hands-free or voice features where you can, and make sure you follow your local laws on handheld devices and microphones in a vehicle. Leave the squelch and volume set sensibly so you don't miss someone calling, and don't tune around or program the radio while moving. Pull over if you need to do more than glance at the display.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.