Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Repeater basics that trip people up: offsets, tones, linking, and etiquette (analog and digital)

ci_cover.jpg

This thread is a place to sort out the questions that come up again and again about repeaters, especially once linking and digital modes get involved. Corrections and local variations are welcome. Band plans and practices differ by country and region, so check your own before programming anything.

Input, output, and offset. A repeater listens on its input frequency and retransmits on its output frequency. The output is the frequency listed in directories, and it is the one you listen to. Your radio transmits on the input, which is the output plus or minus the offset. In North America the common offsets are 600 kHz on 2 m, 5 MHz on 70 cm, 1.6 MHz on 1.25 m, and 1 MHz or more on 6 m. Whether the shift is plus or minus depends on where the output sits in the band, and 2 m is the usual place for mistakes. Other regions use different standards, so use your local band plan and not memory. If you can hear the repeater but it never hears you, check the offset direction and the tone first.

CTCSS, PL, and tone squelch. CTCSS is a continuous sub-audible tone, roughly 67 to 254 Hz, sent along with your voice. Many repeaters ignore a signal without the correct tone, so a stray carrier or distant co-channel station does not key them. "PL" is Motorola's trade name for the same thing and is still used as shorthand. The encode tone is the tone your radio sends. The decode tone is the one your radio requires before it opens its own squelch. On a typical handheld, "Tone" means encode only, and "TSQL" or tone squelch means encode and decode. Some repeaters also send a tone on their output, and some use a different tone on the input than on the output. Most directory listings give the input tone, which is the one you need. If a repeater transmits a tone you do not want to depend on, you can leave decode off.

DCS. Digital Coded Squelch does the same job as CTCSS but sends a low-speed data stream with a three-digit octal code, such as 023 or loosely 754. Many radios let you choose normal or inverted polarity (N or I), and a mismatch there can stop you from getting through. DCS is less common on amateur repeaters than CTCSS. Either way, tone squelch is not privacy. Anyone can monitor with the tone turned off, and it will not stop anyone from hearing you.

Time-out timers and hang time. Most repeaters have a time-out timer (TOT) that drops the transmitter if one user holds the key too long, commonly somewhere around one to three minutes, though it varies by system. Many also use a courtesy tone, which is a beep after each transmission that tells you the repeater has reset and it is safe to transmit again. The "hang time" is the short tail where the repeater keeps transmitting after you let go. Wait for the courtesy tone before keying up, and you will rarely collide with someone or trip the timer. On linked systems the delay can be longer, and several seconds of dead air is normal.

Open and closed repeaters. An open repeater accepts any licensed operator who can reach it. A closed or limited-access repeater is restricted to members or users the owner approves, and may require a particular tone or code to use. Listings often say which it is, but not always. If you are unsure, ask the club or owner before using it regularly. Owners pay for the site, power, antenna, and maintenance, so a club or trustee has every right to set the rules.

Coordination. Frequency coordinators work to keep repeaters from interfering with each other. They typically assign pairs and sometimes tones for a region. Rules vary by country. In the US, for example, a coordinated repeater is generally favored in interference disputes, which is one reason new repeater builders go through coordination first. If you are looking at a repeater that is not in any directory, it may be uncoordinated, private, or simply unlisted.

Linking systems, in one pass each.

EchoLink connects repeaters and individual users over the internet using VoIP, and users must have their licenses validated. Nodes have numbers, and a "-L" suffix usually marks a simplex link and "-R" a repeater link. IRLP is an older VoIP system with numbered nodes and reflectors that relies on dedicated node hardware, and its activity varies by region. AllStarLink is built on Asterisk and lets owners build networks of nodes and hubs, usually controlled with DTMF commands. Wires-X is the Yaesu System Fusion system. It links C4FM repeaters and nodes by room, and rooms can be connected to each other.

DMR is a TDMA digital mode with two timeslots per repeater channel. It uses color codes (0 to 15), talkgroups, and DMR IDs registered to the operator. Color codes serve a role similar to access tones, but talkgroups and timeslots determine where your audio goes, and different networks carry different talkgroups. D-STAR uses callsign routing, with RPT1 and RPT2 fields, a UR call, and reflector links. Both modes need correct programming in the radio, and a plan that works on one repeater may not work on the next without changes. Digital repeaters often carry nothing on a channel that sounds silent to an analog radio, so do not assume it is dead.

Etiquette basics. Listen before you transmit, especially on linked systems. Give your call sign, and pause between transmissions so others can break in. Keep transmissions short, and do not key up just to test whether it works ("kerchunking"). Identify as your license requires, and leave room for emergencies. Do not link or tie up a linked system without knowing what it is connected to. And when a net is running, do not interrupt it unless you have something for it.

Finding repeaters. Directories such as RepeaterBook and the ARRL directory list frequencies, offsets, tones, and modes. They depend on owners and users to keep entries current, so check the club's site when something looks out of date. Local repeater clubs often publish their own lists, net schedules, and rules, and joining one is a direct way to support the machine you use.

What are the questions you see newcomers ask most? And which of the above would you add to or correct?

  • Replies 2
  • Views 39
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One addition on tones: the most common reason someone can hear a repeater but not get into it is a wrong or missing encode tone. The second is a reversed offset. Many radios can monitor the input frequency, often through a "reverse" function. If you hear the other users directly on the input, you are probably in simplex range of them, and a repeater is not needed. That is a useful check before you spend time fixing a signal-strength problem.

It also helps to know which tone a directory lists. Some list the input tone and some list the output tone. Where a repeater uses a different tone for each, the listing may only give one, so a call to the owner or a look at the club's page can save a lot of guessing.

On linked systems, a good habit is to leave a longer pause than feels natural. Between the link delay, a node dropping in, and a time-out timer resetting, people who jump in right after the courtesy tone often step on each other.

  • Administrators

On the digital side, the biggest mistake is treating it like analog with a different sound. On DMR, your radio's codeplug has to match the repeater: frequencies, color code, timeslot, and the right talkgroup for the audio you want. If you pick the wrong timeslot, the repeater may hear you but not route you, or you may land on a talkgroup that is busy and disrupt a QSO on a different timeslot. Many networks also publish rules on what talkgroups are for, so read before you key up on a wide-area one.

For D-STAR and Wires-X, the equivalent habit is to learn what the repeater is connected to before you transmit. A reflector or room may have dozens of listeners in different places. A quick "is this frequency in use?" can reach people far away, so listen for a while first. Most dashboards for the networks show what is currently linked.

For AllStar and EchoLink, many nodes have posted rules, such as which hours they are linked or which commands are allowed. Some sysops lock out DTMF control for non-members. If a command fails, it may be intentional, not a fault.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.