Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Clean SSB audio: mic gain, ALC, compression and filters, and what actually helps on weak-signal and DX contacts

ci_cover.jpg

Most SSB audio problems come from a handful of settings that interact with each other: mic gain, speech processor level, ALC, TX bandwidth and EQ. Many operators fix one and break another. This thread is for comparing approaches and sorting out which adjustments matter when the signal is marginal.

Here is a framework to start from. Set the mic gain first, with the processor off. Speak at a normal, steady level and watch the ALC meter. Peaks should just touch the ALC zone, not sit deep inside it. If the ALC is pinned on every syllable, the audio stage is overdriven. That causes flat-topped distortion, splatter on adjacent frequencies, and a harsh sound that is harder to copy, not easier. Power output on SSB depends on average speech level, but pushing the mic gain is the wrong way to raise it. Ideally the ALC only limits occasional peaks.

Then add the processor. Compression raises the average level relative to the peaks, which helps under noise. Moderate settings usually work best. Heavy compression also lifts room noise and breath sounds, and it can squash the dynamics that make speech intelligible. On many radios the compression meter has a suggested range in the manual, so check yours. Re-check ALC after any processor change, because the two are linked.

For EQ, the usual goal is intelligibility rather than fullness. Trim low frequencies below roughly 150 to 200 Hz, because they use transmit power without helping copy. A modest lift in the 1.5 to 3 kHz region can add articulation. Boosting high frequencies mostly adds sibilance and splatter risk. Start with small changes and A/B them with a monitor or a recording rather than by feel alone.

On bandwidth, 2.4 kHz is a common receive filter width and a reasonable TX bandwidth target. A wider TX setting sounds more natural on a quiet band but uses more spectrum. Narrow it when the band is crowded or the signal is weak. Convention is USB above about 10 MHz and LSB below, with 60 meters using USB. Following it keeps you on the same side as everyone else.

Questions for the thread: how do you decide between a lower and higher TX bandwidth? Do you prefer RF or AF compression where your rig offers both? And what is your method for checking your own audio, such as a monitor with headphones, a recording, a second receiver or an SDR, or reports from other stations?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One thing worth adding about the monitor function: it is useful, but know what your rig is feeding it. On some radios the monitor takes audio before the processor, and on others it is tapped after it. If you tune the sound in your headphones without knowing which, you may be judging a signal that is not what goes out on the air. Wear headphones so the monitor does not feed back into the mic, and compare against a recording, a remote SDR or an on-air report when you can.

Microphone technique matters as much as any menu. Keep a consistent distance from the mic, and use a pop filter or foam windscreen to tame plosives. Be aware of proximity effect: close up, a directional mic boosts the low end, so an EQ low cut that sounds right at one distance may sound thin at another. A stable position, usually a few inches off-axis, gives a more predictable signal than constant EQ changes. Also reduce room reflections and fan noise before turning up the processor, because compression will amplify them.

  • Administrators

For weak stations and DX, readability matters more than sounding good. The transmit side is mostly about not wasting power: low-cut EQ, a modest amount of compression, ALC kept under control, and a clean linear amplifier if you run one. Overdriving the amp is a common cause of splatter that makes you unpopular and does nothing for your signal at the far end. Speak clearly and unhurried, and use standard phonetics for callsigns, because distinguishing similar-sounding letters is hard through QSB and noise.

On the receive side, a narrower filter, maybe 1.8 to 2.4 kHz depending on conditions, can cut adjacent-channel QRM. Try the filter shape and passband shift before leaning on noise reduction, which can add artifacts on a weak signal. Choose AGC speed deliberately, and use the preamp only when the noise floor allows it. In a DX pileup, find out whether the station is working split and listen to where they are answering. Then send your callsign once, at the right time, rather than repeating it over other callers. Check that your TX and RX frequencies are set as intended before you key up.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.