Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a wire antenna from scratch: what do you decide first, and where do homebrew builds usually go wrong?

ci_cover.jpg

This thread is for the practical side of homebrew wire antennas, such as dipoles, inverted Vs, simple verticals and fed wires. Below is a rough order of decisions that helps, followed by the usual trouble spots. Please add corrections, because a lot of rules of thumb here depend on the situation.

Start with the feed system, not the wire. The decision that shapes everything else is whether you feed with coax or with balanced line. A resonant half-wave dipole fed with 50 ohm coax through a current balun or choke is the simplest single-band build. If you want several bands from one wire, a dipole or doublet fed with ladder line (roughly 300 to 600 ohms) and a tuner that can handle the high-impedance mismatch is often more efficient than a coax-fed multiband antenna, because ladder line has low loss even at high SWR. Coax with a high SWR can lose a surprising amount of power, especially on the higher bands and with thin cable.

Wire and length. For a half-wave dipole, the starting formula is about 468 divided by the frequency in MHz, giving the total length in feet. At 7.1 MHz that is about 65.9 ft, or 32.9 ft per leg. Treat it as a starting point only. Height above ground, nearby objects, wire diameter and insulated versus bare wire all move the resonant frequency. Insulated wire usually resonates lower than bare wire, so cut long and trim. Hard-drawn or copper-clad steel wire in around 14 AWG is a common compromise: it resists stretching and survives weather. Stranded and soft-drawn copper stretches over time, which slowly changes the resonance. Thinner wire works for lightweight portable use but breaks more easily.

Insulators and supports. End insulators carry the full wire tension, so choose ones rated for UV and weather. Plastic, ceramic or glass types all work if the wire is anchored without sharp bends that cut into it. For rope, UV-resistant polyester stays at length better than nylon, which stretches and sags. A center insulator should have strain relief so the coax or ladder line weight does not pull on the solder joints. Seal the coax end against water, since wicking into the braid is a common reason for a slow rise in SWR. For fiberglass poles, keep them well away from power lines and check how much wind load the wire adds, because a pole that holds a vertical wire may not handle an inverted-V apex.

Baluns and chokes. A dipole is balanced and coax is not, so without some form of choke the outside of the coax shield can carry common-mode current and become part of the antenna. This can cause RF in the shack, a distorted pattern and noise pickup. A simple choke can be several turns of the coax itself wound on a suitable ferrite core, usually a type 31 or 43 mix, or a stack of ferrite beads over the coax. Which mix and how many turns work best depends on the band, so the choke should be sized for the frequency range you plan to use. A 1:1 current balun at the feedpoint is a standard answer for a dipole, and a 4:1 or 9:1 unun or balun is used at other impedance points, such as an off-center-fed dipole or an end-fed wire.

Verticals and radials. A quarter-wave vertical is roughly 234 divided by the frequency in MHz, in feet. For a 14.2 MHz vertical that is about 16.5 ft. A vertical needs a counterpoise, because the radiating current has to return somewhere. With elevated radials, a small number of resonant radials (often four to sixteen) can work well. With radials on or in the ground, more wires generally help because ground losses are the main enemy. Radial length matters less on the ground than for an elevated, tuned set. Remember the ground system when you do the modeling, since the model should show the same trend.

Tuned and trap antennas. Trap dipoles and verticals save space and give multiband operation without a tuner. The price is lower bandwidth, some added loss in the traps, and extra tuning work because each trap affects the lengths of the sections beyond it. Home-built traps need careful measurement, such as using a grid dip meter or an analyzer to check each trap frequency before installing it. Fan dipoles, where several wires share one feedpoint, are mechanically simpler, though the elements interact and need trimming.

Measuring SWR. An antenna analyzer at the feedpoint tells you the most about the antenna itself. Measuring at the radio end shows the SWR after coax loss, which can make a poor antenna look better than it is. If the analyzer reads a good SWR at a different frequency than expected, find out why before trimming blindly: nearby metal, the height, a choke problem or a wrong velocity factor all produce this. Check with the coax moved or the choke changed. If the reading changes, the feedline is involved.

Modeling. EZNEC and MMANA-GAL are both useful before cutting wire. They are not magic, and the results depend on correct inputs: the real wire diameter and material, the height, the ground type, and a sensible segment count. Check your model against a known case, such as a half-wave dipole at a given height over average ground. MMANA-GAL is quick for comparing shapes and getting rough patterns, while EZNEC with its NEC core is better for detailed ground and feedline setups. In either program, a large gap between model and measurement points to a modeling error or a real-world problem such as common-mode current.

What are you building, and what are you stuck on? Band, available supports and feedline type are the things that most affect the advice.

  • Replies 2
  • Views 30
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One thing worth adding on the choke question: the best place for it depends on the antenna. For a coax-fed dipole it belongs right at the feedpoint, because that is where the imbalance starts. A second choke further down the line is a reasonable addition when the feedline runs near other wiring or into the house. For an end-fed wire with no real counterpoise, the coax shield often becomes the counterpoise, so a choke at the feed end can actually change the resonance and the SWR. That is why some end-fed designs include a short dedicated counterpoise wire and a choke after it, and why the measured numbers can shift when you move the coax.

On wire, one practical note: when you trim a dipole, change both legs equally to keep it balanced, and go in small steps, since the resonant frequency moves by a fairly large amount per inch on higher bands. Marking each leg with tape at the original length makes it easier to go back if the trim overshoots.

  • Moderators

For modeling, it helps to run a few sanity checks so you can trust the results. First, put a plain dipole at your planned height and compare the resonant frequency with what you measure later. Whatever offset appears is a correction factor you can apply to other models of the same site. Second, check the segmentation: very short segments next to a junction or a much longer one can cause average-gain-test warnings, and in MMANA-GAL the average gain test is a quick way to see whether the model is reasonable. Aim for an average gain close to 1 (0 dB) with a lossless setup.

Also check how the program treats ground, since radial-heavy verticals and low horizontal wires depend on it. For a vertical, run the model with different radial counts or ground types to see how much the efficiency and takeoff angle change. That gives you a sense of whether extra radials are worth the work before you cut anything. And for ladder-line setups, model the antenna alone for pattern and impedance, then handle the feedline loss and tuner matching as a separate calculation, because the SWR on the line and the loss in the line depend on the cable type, length and frequency.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.