Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a first portable QRP setup: rig, antenna or battery, where does the effort pay off?

ci_cover.jpg

This is a discussion starter for anyone planning a low-power portable station, or rethinking one. The usual QRP definition is 5 watts output on CW and 10 watts PEP on SSB, which is how QRP-ARCI contests treat it. Plenty of people say "5 watts" for both modes, so it helps to say which you mean when you compare notes.

The rig choices cover a wide range. The Elecraft KX2 and KX3 are full multimode transceivers with roughly 10 W maximum output, so SSB and digital modes are possible as well as CW. The Mountain Topper (MTR) series is much smaller: CW-only, 5 W class, and built around summit activations, with different models covering different band sets. The Penntek TR-35 is a compact single-band 5 W CW kit, so you choose the band version you want. Hendricks kits sit in the traditional build-it-yourself camp. Pixie-style kits are at the extreme end. They are cheap, tiny, run a few hundred milliwatts at most, and have famously wide, rough receivers. As a first soldering project they are great fun, but not a good measure of what QRP can do.

For comparison, 5 W versus 100 W is a 13 dB difference, about two S-units. A 3 dB antenna improvement is the same as doubling your power, so a resonant antenna at a decent height is usually worth far more than another watt or two. The common field antennas are an end-fed half-wave with a matching transformer (49:1 or 64:1 are the usual ratios), a resonant dipole or inverted-V on a lightweight mast, a linked dipole for multiband use, or a vertical with a few radials. Keep the feedline short and low-loss, because thin coax like RG-174 wastes a surprising amount at higher HF bands.

On power, LiFePO4 has become popular. A 4S pack is about 12.8 V nominal, around 14.4 to 14.6 V fully charged, and the discharge curve is very flat. Check your rig's maximum input voltage before you plug one in. As a rough guide, a 6 Ah pack at 12.8 V holds about 77 Wh. Receive current matters as much as transmit current on CW, because you spend most of your time listening.

For calling frequencies, the commonly published CW QRP spots are near 1.810, 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz. SSB QRP is often listed near 3.985, 7.285, 14.285, 21.385 and 28.885 MHz. Check them against your local band plan and current usage, since conditions and regional rules vary.

Where would you put your money and effort first, in the rig, the antenna system, or the power supply? And does anyone think SSB QRP is worth the trouble compared with CW?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Antenna first, and it isn't close. The rig only changes what you can do with the signal you already have, while the antenna changes how much signal you have. An end-fed half-wave is convenient, but the matching unit and the coax run out to the radiating wire both cost you something. A resonant dipole or inverted-V fed directly usually gives the cleanest, most predictable result if you have two supports. For portable work, a roll of thin wire, a lightweight fishing pole and some cord make a very capable kit.

On SSB versus CW, they are different games. With 5 W CW you can pull a signal out of noise using a narrow filter and a trained ear. SSB needs a much stronger signal to be copyable, so QRP SSB tends to work best on a good band with a good antenna, mostly when the other station is also listening for weak signals. The KX2 and KX3 make SSB practical, but CW is where QRP gets the most out of every watt.

  • Moderators

Don't ignore the power side, because it is where field setups quietly fail. A battery that sags under transmit load can make a rig misbehave, and some radios show reduced output or odd behaviour well before the pack is empty. LiFePO4 helps because of the flat voltage curve, but check the full-charge voltage against the radio's limit. Most hold up fine, but it is worth confirming rather than assuming. Also look at the connectors, fuse and cable gauge. Poor DC leads cause more voltage drop than people expect.

For kit builders: a Pixie is a great first project because you learn how a transmitter, receiver and sidetone fit together, but expect very limited selectivity. If you want a kit you will actually use on air, look at something like the TR-35 or a Hendricks design, and plan for a proper case and key connection. Then try the QRP-ARCI sprints and QSO parties. They are a good way to find out what your station can really do, since many of the people you hear are running low power too. Read the rules for each event first, since power limits and exchanges differ.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.