Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Before the first on-air contact: how do you verify a homebrew QRP transmitter (Tuna Tin 2, Pixie, BITX or uBITX)?

ci_cover.jpg

Building a small transmitter is only half the job. The other half is knowing what it sends out. A Pixie, a Tuna Tin 2 style crystal oscillator and amplifier, a BITX board or a uBITX can all make contacts at a few watts or less, but the same circuits can also put out harmonics, spurs and unstable keying if nobody checks them. I'd like to compare notes on a bench routine that doesn't need expensive gear.

1. Start with a dummy load, not an antenna. A 50 ohm non-inductive load rated well above your output power is the first thing to connect. Many carbon-composition or metal-film resistor loads work for a few hundred milliwatts. For higher power, use several resistors in parallel and check them for heating.

2. Measure power with an oscilloscope if you have one. Put a 50 ohm termination across the output and read the peak-to-peak voltage. Into 50 ohms, P = Vpp² / 400. Ten volts peak-to-peak is about 0.25 W, and 20 Vpp is about 1 W. It only works for a clean sine wave on a scope with enough bandwidth, so treat it as an estimate. If the waveform looks like a lumpy square wave, harmonics are almost certainly present.

3. Look at the spectrum. A spectrum analyzer is ideal, but a calibrated attenuator plus an SDR receiver or a second receiver is a workable substitute. Add enough attenuation that the front end can't overload, because an overloaded receiver will show harmonics that don't exist. Tune to the second and third harmonics and compare their level to the fundamental. Rules vary by country and by power level, so check your own regulations for the required suppression. Modern practice generally expects a good deal more than a bare transistor stage gives you.

4. Don't skip the low-pass filter. A Pixie with no output filter, or a Class C or Class E stage, can be rich in harmonics. A suitable low-pass filter for the band is part of the transmitter, not an optional accessory. On a multiband rig like the uBITX, check each band, since the filter selection and the drive level can differ and a filter that is fine on one band may be marginal on another.

5. Check keying and the power supply. Listen to your own signal on a separate receiver. Hard keying of an oscillator can produce clicks, and supply sag can produce chirp. Sags and ripple both end up on the signal, so try a regulated supply, bypass capacitors close to the stages, and a series fuse. A reverse-polarity diode or a fuse is cheap protection for a kit you spent hours on.

6. Only then connect the antenna and check SWR. Before trusting a homebrew SWR bridge, test it with the dummy load. It should show a good null, with essentially zero reflected reading, and a clearly bad reading when you open or short the output for a moment at low power.

What does your own bring-up routine look like, and which of these steps do you think builders skip most often?

  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Good list. I'd stress the attenuator point for anyone using an SDR dongle as a poor man's analyzer. If you connect even a watt directly to the input, you can damage it, and a milliwatt-level signal can already overload it. Use a known attenuator chain, such as a few fixed pads or a tap from a directional coupler, and keep the numbers written down so you can add them back when you read the harmonic levels.

Also confirm that what you see is real. If the third harmonic seems to move in level when you add or remove attenuation, the receiver is overloading. A correct reading should drop dB for dB as you add attenuation. Images and aliasing in cheap SDRs can show up as phantom signals, so check by moving the tuning slightly or by changing the sample rate.

On the Pixie, don't expect miracles from the stock circuit. It works as a learning project and for very short-range CW, but a low-pass filter on the output makes it a much better neighbor on the band.

  • Moderators

One thing I'd add to the filter step is that you can test the low-pass filter on its own before it ever sees RF power. A NanoVNA-type instrument can plot S21 through the filter, so you can see the cutoff, the passband loss and how deep the stopband goes at the second and third harmonic. Make sure the filter is terminated sensibly, and never connect a transmitter to the VNA ports.

Component tolerance matters more than people expect. Toroid turns spacing and capacitor values shift the cutoff, so a filter built exactly to a table can still be a bit off. If the passband is lossy or the cutoff sits too close to the operating frequency, adjust the toroid turns by spreading or squeezing them, or swap in a close-value capacitor, and re-sweep.

For the keying check, a direct-conversion or crystal-controlled rig can sound very different on a second receiver than in the sidetone. Listen for chirp when the supply is shared between the oscillator and the amplifier, and consider a separate regulator for the oscillator. A few milliseconds of rise and fall time on the keyed stage often cleans up clicks without hurting readability.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.