Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Multi-day EMCOMM station: LiFePO4 primary, generator backup, solar trickle. What would you change in this layout?

ci_cover.jpg

I'm sketching a standard field station layout for a multi-day EMCOMM deployment and want to pressure-test it before it turns into a checklist. The goal is one HF rig (NVIS-capable), one VHF/UHF rig for local nets and repeater or simplex work, a laptop for digital modes and logging, and a few small loads like lighting, a phone charger and a router. The location is an open field with a pop-up shelter. Assume no grid power, and that the station has to stay on the air through a storm and overnight.

Power plan as it stands: a 12.8 V LiFePO4 battery as the primary source, sized for roughly 24 hours of expected load with margin. A 200 to 300 W solar panel through an MPPT controller set to a LiFePO4 profile tops it up during the day. A small inverter generator sits well downwind as backup, feeding a 12 V charger or power supply, so the battery is the only thing the radios ever see. Everything off the battery goes through a fused distribution block with Powerpole connectors, with the main fuse close to the battery positive terminal. The radios get their own fused leg, and accessories are on a separate one.

Antenna plan: a 33 to 40 ft fiberglass telescoping mast, guyed in three directions, holding either the center of an inverted-V dipole for 40 m and 80 m, or a multiband end-fed with a counterpoise, plus a separate J-pole or small vertical for 2 m/70 cm on its own short mast. A common-mode choke goes at the feedpoint and another where the coax enters the shelter. The HF feedline is RG-8X or similar because it's lighter, and the VHF/UHF run uses a lower-loss cable like LMR-400 class if the run is more than a few meters.

The questions I'd like input on:

First, LiFePO4 behavior under load. The BMS can cut off suddenly at low voltage, which would drop the whole station with no warning. Is a voltage monitor with an alarm enough, or is there a better way to give yourself a graceful shutdown margin?

Second, noise. MPPT controllers and cheap inverters can wipe out the lower HF bands. Where do you place the controller relative to the antenna and the radio, and do you plan ferrites on the DC leads from the start or only after you hear a problem?

Third, grounding. In a field with no good soil access, what does a reasonable 'ground' even mean? I'm leaning on the feedpoint choke and a counterpoise, and treating a ground rod as a mostly safety and static-bleed measure rather than as something that makes the antenna work. Is that the right framing?

Last, teardown. We tend to over-plan setup and wing teardown. What belongs on the teardown checklist besides the obvious (fuel, stakes, trash)?

  • Replies 2
  • Views 20
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the LiFePO4 cutoff: don't rely on the BMS as your low-battery warning. LiFePO4 has a very flat discharge curve, so the voltage looks fine until it suddenly isn't. A voltage reading is a poor fuel gauge for this chemistry. A shunt-based battery monitor that tracks amp-hours consumed gives you a real state of charge, and you can set an alarm at something like 20 to 30 percent remaining. Keep the voltage alarm as a second layer, but treat it as the last warning rather than the first.

Also check the voltage under load, not just at rest. A healthy LiFePO4 pack runs about 13.2 to 13.3 V for much of its discharge and sits around 14.2 to 14.6 V when charging. Most modern HF rigs are happy anywhere in a 13.8 V ±15% window, but older rigs or ones with a tighter spec may complain at the top of the charging range. If your radio is picky, check its manual for the maximum input voltage before you wire it directly to a battery that's being charged.

For noise, I'd plan the ferrites from the start. They're cheap and they take almost no space in the kit. Put clamp-on or toroid ferrites on the solar input, the controller output, and the DC leads to the radio. Then do a noise-floor test during setup: with the radio on a band you plan to use, switch the controller on and off, and the generator too, and note any change in S-meter reading. Keep that test as a line item on the checklist, because noise problems often depend on the specific band and on how the cables lie that day.

  • Moderators

Your framing of grounding is basically right. A ground rod that's a few feet long won't do much for the RF performance of most field antennas, but it can bleed off static and give you a reference for equipment bonding. The bigger things are a well-placed choke on the feedline and a counterpoise or radial set that suits the antenna. An end-fed or vertical with no counterpoise will use your coax shield as one, and that's how you end up with RF in the shack and a noisy receive. Chokes at both ends of the coax are cheap insurance. For lightning, no field ground setup is protection. The rule is to monitor the weather, disconnect the feedlines from the radios, and move people away from the mast when a storm gets close.

A few safety items that belong on the setup list: pick the mast location by looking up first, and keep the whole mast, with guy lines and a margin for it falling, clear of any overhead power line. Put the generator at least 20 ft from the shelter with the exhaust pointing away from tents, and have a battery CO alarm inside. Don't connect the generator to the station wiring in any way that could backfeed anything. Check your generator's manual about neutral bonding if you ever run AC through a distribution strip, and leave the layout as 12 V only unless you have a reason otherwise.

On the coax: at 2 m, RG-58 class cable loses roughly 4 dB per 100 ft and LMR-400 class about 1.4 dB, and the gap widens at 70 cm. For HF, loss is negligible over a short run, so RG-8X is fine. The real cost of coax on HF is the weight pulling on the mast, so use a strain relief and don't let the cable's weight hang on the feedpoint.

For teardown, add these: photograph or note anything that failed or was awkward before packing it away, return the battery to a storage charge level rather than leaving it empty or full, check the fuses and connectors for heat discoloration, dry the guy lines and tent before bagging, count the stakes and the Powerpole pigtails, and log the final hours of generator runtime so the next deployment knows what the fuel plan really was.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.