Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Where dynamic range actually gets lost in an SDR chain: gain, filters, upconverters and antennas

ci_cover.jpg

A lot of SDR troubleshooting threads boil down to the same symptom: the waterfall is full of signals that shouldn't be there. Ghost carriers, FM broadcast images in the airband, a noise floor that jumps when you touch the gain slider, or an HF band that looks like a comb. The usual advice is to turn the gain down, but that skips over why it works. So here is a framework for discussion: where in the chain do you run out of dynamic range, and what can you actually do about it?

Start with the ADC. An RTL-SDR dongle uses an 8-bit converter, which gives a theoretical ceiling of roughly 48 dB of dynamic range. That is before the tuner's own limits and before real-world ADC imperfections. Receivers like the SDRplay RSP series, Airspy R2/Mini, LimeSDR and the Airspy HF+ line use higher-resolution converters, and that gives you more room before a strong signal pushes the weak ones into the quantization noise. Bit depth is not the whole story, though. Linearity of the front end (the LNA, mixer and any AGC stages) usually determines whether strong out-of-band signals create intermodulation products inside your passband. A wideband receiver sees everything the antenna delivers, not only what is displayed in the waterfall.

This matters for the sample rate setting. Running 2.4 MS/s or 10 MS/s lets you see a wide slice of spectrum, but the ADC and front end are handling the total power of everything in that slice and often well beyond it. If a few strong FM broadcast stations or a pager transmitter are nearby, they can dominate the converter even when you are listening to a narrow signal. That is why a broadcast-FM notch filter, or a bandpass filter for the band you care about, often improves things more than a more expensive dongle would.

For setting gain, a practical method is to watch the noise floor, not the signal. Connect the antenna and raise the gain until the noise floor rises noticeably above what you see with the antenna disconnected or terminated. That tells you the receiver is no longer the limiting factor. Past that point extra gain mostly eats headroom. If a strong signal makes the whole waterfall breathe or creates symmetric copies of itself at other frequencies, you are overloading something and should reduce gain or add filtering ahead of the receiver. Also check whether the AGC in your software or driver is fighting you. Some drivers and tools let you set tuner gain stages individually, which helps when one stage is the problem.

HF is a separate case. Most RTL-SDR dongles don't cover HF in their normal tuner range. Options are direct sampling mode, available on some models and fairly limited in performance, or an upconverter that shifts HF up into the tuner's range. With an upconverter you have to account for the local oscillator offset in your software. SDR# can handle it with a frequency shift setting, and some SDR hardware and software combinations have built-in support. Watch for LO leakage and spurs, and keep the converter away from noisy USB hubs and switching power supplies. Hardware designed for HF, such as the Airspy HF+ series or SDRplay units with good HF filtering, avoids this extra stage but costs more.

On HF the antenna and local noise usually dominate before receiver sensitivity does. A noisy LED supply, a USB 3 cable or a computer monitor can raise the noise floor across several bands. Ferrite chokes on the USB and coax, a feedline that is physically separate from the computer, and a proper common-mode choke at the antenna feedpoint can change what you hear more than any receiver upgrade. For VHF and UHF, an LNA close to the antenna, preceded by an appropriate filter, usually beats an LNA at the receiver end of a long coax. Note that an LNA with no filter will often make overload worse.

Then there are the software tools and what each is good at. SDR# is popular on Windows and has a large plugin ecosystem. SDRuno is specific to SDRplay hardware and has sophisticated filtering and multi-receiver features. HDSDR is a Windows choice with an ExtIO driver interface, often used for HF and with CAT control. GQRX is the common option on Linux and macOS and works with SoapySDR and osmosdr-supported hardware. CubicSDR is cross-platform and also works through SoapySDR. For decoding, you usually pipe or route audio to another program: WSJT-X or fldigi for digital modes, multimon-ng for pagers, rtl_433 for ISM-band sensors, dump1090-type tools for ADS-B. A virtual audio cable is the most common connection method on Windows, with equivalent loopback devices on other systems.

Finally, panadapters and bandscopes. A panadapter takes a sample of a transceiver's IF or a separate receive path and shows the surrounding band on a waterfall, with CAT control keeping the SDR synchronized to the radio. The key rule is to protect the SDR from your own transmitter. Do not connect an SDR directly to an antenna that your transceiver transmits on. Use the radio's dedicated IF output, a proper RX-only antenna, or a switching and attenuation arrangement designed to survive TX power.

Questions for the thread: what is your approach to choosing between filtering and a better receiver? Where do you place the LNA? And for those running a panadapter, which method do you use for TX protection?

  • Replies 2
  • Views 34
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the gain procedure: I'd add that it's worth checking for overload with a test that doesn't depend on the waterfall alone. Change the gain by a few dB and see if weak signals move by the same amount. Real signals should move with gain. Intermod products and images will often move by a different amount, or appear and vanish. If a spur moves by more than the gain step, it was probably created inside the receiver rather than arriving from the antenna. Another quick check is to insert an attenuator ahead of the receiver. A real signal drops by the attenuator value, while a product from overload usually falls faster, because intermodulation products scale nonlinearly with input level.

On filters versus a better receiver: it depends on which problem you have. If the problem is a strong nearby signal outside your band of interest, a filter (FM notch, bandpass, or a cavity for narrow bands) addresses the cause directly, and a higher-bit receiver only gives you more room. If the problem is a very wide spread of signal levels inside your band, which is common on HF in the evening, then you need the better ADC and front end. Often it's both.

  • Administrators

On LNA placement, the standard rule is that the noise figure of the first stage dominates the system. Loss in the coax before an LNA adds directly to noise figure, so at 1090 MHz for ADS-B or 137 MHz weather satellites, putting a filtered LNA right at the antenna is generally the better arrangement. The filter matters, though. A cheap broadband LNA can push strong out-of-band signals into overload, so a band-specific filter is often chosen to go with it. Check also how the LNA is powered. A bias tee sends DC up the coax, and you want to be sure that the DC does not reach anything that cannot handle it, such as a splitter without DC pass, or a different antenna.

For the panadapter safety question: the safest options are an IF tap if your transceiver offers one, or a separate receive antenna. If you must share an antenna, a purpose-built TX/RX switching arrangement, with the SDR path grounded or isolated during transmit, is what you want. A passive splitter is not protection. Even low-power transmissions can exceed what an SDR front end tolerates, so confirm the power levels in the manuals for both devices before connecting anything.

For HF with upconverters, one more detail: calibrate the offset. A converter with a crystal LO has its own frequency error, so signals will be off by an amount that scales with the LO frequency. If you decode weak-signal modes such as FT8, check a known carrier and correct it in the software, or tolerate it where the mode permits a wide enough frequency window.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.