Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24–48 hour EMCOMM field station: how are you splitting power, antenna and noise decisions?

ci_cover.jpg

I'm putting together a repeatable plan for a 24–48 hour field deployment: a served-agency tent or shelter, one HF station, one VHF/UHF station, and possibly a digital station on a laptop. The goal is a layout and checklist that a different operator could set up from a printed sheet, so I'm trying to pin down the decisions that matter most before worrying about brands.

Here is the rough framework I'm working from.

Power budget first. Before choosing a battery or generator, list every load with its receive and transmit current, then estimate duty cycle. A 100 W HF rig can draw roughly 20 A at 13.8 V on transmit and only a few amps on receive. A laptop, a radio-interface box, lighting, a phone charger and a small fan add up over a full shift. Multiply average amps by hours to get amp-hours, then add margin. I'd rather size for a pessimistic duty cycle than discover at 3 a.m. that the battery is at 20%.

Primary and backup power. One option is a LiFePO4 battery as the primary, with an inverter generator as the recharge source and solar as a trickle or top-up. The generator then only runs when needed, which cuts noise, fuel and the RF hash it can produce. Distribution would be a fused panel on the battery with Powerpole outputs, and a fuse as close to the battery positive terminal as practical.

Antennas and coax. I'm leaning toward a simple, fast-to-deploy antenna per band group instead of one clever multiband system. Examples are a vertical or end-fed wire on a telescoping mast for HF, and a roll-up or mast-mounted J-pole or vertical for VHF/UHF. I want to keep coax runs short, put the feedline choke at the antenna feedpoint or where the line enters the shelter, and make sure the mast and guying survive an afternoon wind shift.

Grounding and safety. I'm separating three things that often get lumped together: the generator's safety ground and bonding, the station bonding between radios, supplies and the distribution panel, and any RF or lightning-related practices. I'd like to hear how others document these so a new operator doesn't improvise.

Open questions:

  • How far from the shelter do you place the generator, and how do you manage exhaust direction and CO risk?
  • What's your minimum for noise mitigation (chokes, separation, cable routing) before you declare the station ready?
  • What's on your setup and teardown checklist that people tend to forget?
  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Your power budget step is the right place to start. Two details are easy to miss. First, size the wire for the worst-case load, not the average. At 20 A or more on a 12 V system, voltage drop is real, so keep DC runs short and use adequately heavy conductors. A rig that sags to 11 V on voice peaks can splatter or shut down even when the battery is fine. Second, check the battery's rated continuous discharge and the BMS cutoff. Some small LiFePO4 packs have a BMS limit that a 100 W rig plus accessories can trip, and the radio just dies with no warning.

On LiFePO4 specifically, read the manual for charging temperature limits. Most cells should not be charged below freezing unless the pack has low-temperature protection or a heater. If you plan to charge from a generator or solar on a cold morning, that matters. Also make sure the charger or MPPT controller has a LiFePO4 profile. A generic lead-acid charger may not fully charge it or may overcharge it.

For solar, an MPPT controller with a panel sized for a few hours of sun can carry the receive-heavy baseline load of a net-control station, but don't count on it for HF transmit without a lot of panel. I'd treat solar as extending the battery, not replacing the generator, unless the deployment is long and the loads are small.

On generator placement, the usual guidance is to keep it well away from tents and openings, downwind, on level ground, with a battery-powered CO alarm in the shelter. Treat that as a hard rule on the checklist, not a preference. Also plan for refueling. Let it cool first, and keep fuel away from the generator and the shelter.

  • Moderators

For noise, I'd make it a test step in the setup sequence. Power up everything in the order you expect to run it, then tune across your working bands with the generator on and off and note what changes. Common culprits are switching power supplies, laptop chargers, USB hubs, LED lanterns, and the generator's own inverter. Fixes tend to be mundane. Separate the antenna from power and data cables, use clip-on ferrites or chokes on DC leads and USB cables, and put a common-mode choke on the coax. Also try moving the antenna farther from the shelter. A few extra meters of separation often does more than any ferrite.

On coax, use the shortest run that gets the antenna clear of obstructions and the shelter. Loss depends on the cable type, frequency and length, so check the manufacturer's attenuation chart for your cable at 2 m and 70 cm. It is usually the VHF/UHF runs where cheap thin coax hurts most. Add weatherproof connectors, strain relief so the mast doesn't pull on the radio, and a drip loop where the coax enters the shelter.

For masts, the safety checks should be unambiguous. Look up for power lines before raising anything, and keep the full mast height, plus a generous margin, clear of any line in every direction it could fall. Guy the mast where the manufacturer specifies, stake it so it can't be dislodged by a vehicle or foot traffic, and put flagging on guys. If thunderstorms are near, the plan should say to stop operating, disconnect and lower the antenna if it's safe, and move people to a proper shelter. A tent is not lightning protection.

For the teardown checklist, add: power down radios before disconnecting, stow coax with connector caps on, count stakes and guy lines, photograph the site for a final check, bag trash and cut cable ties, and log battery state of charge and generator fuel so the next team knows where things stand. A final line item I like is a short written note on what failed or was missing, so the checklist improves after every deployment.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.