Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig triage: how do you separate power, receive and transmit faults before pulling the finals?

ci_cover.jpg

A rig that is dead, or that receives but won't transmit, often gets blamed on the finals straight away. Final transistors do fail, but a lot of "blown PA" diagnoses turn out to be a supply, a protection circuit or a bias problem. Here is the order I'd suggest for narrowing it down, and I'd like to hear where others change it.

1. Power first, and under load. Check the voltage at the rig's power connector, not at the supply terminals. Then check inside the rig after the fuse and the reverse-polarity protection. A fuse can look fine and still have high resistance, and a connector can read 13.8 V unloaded and sag badly when the rig draws current. Watch the voltage while keying a transmit into a dummy load. If you have a scope, put it on the supply rail with AC coupling. Excess ripple or switching hash points to a failing filter capacitor or a noisy switch-mode supply.

2. Decide whether it's one fault or two. No receive and no transmit at the same time usually means something shared: the supply rails, a regulator, the reference oscillator or PLL, the CPU or its reset, or the antenna relay or TX/RX switching. Two independent failures are much less likely. Check the regulated rails (for example 8 V, 5 V, 3.3 V) against the service manual, and confirm the reference oscillator is running with a scope or a frequency counter.

3. No receive, transmit okay. Work from the speaker backward: audio amp, volume control and squelch, then detector, IF and mixer, then the front end. Injecting a signal from a generator, or even a clean test tone at various points, tells you where the signal disappears. Also check that the receive path isn't being disabled by a stuck relay, a dirty switch contact or a bad PIN diode switch.

4. No transmit, receive okay. Check the PTT line and whatever mutes the receiver when keyed. Then see whether you have drive at the driver stage, whether the bias is present, and whether the ALC or protection circuit is clamping the output. A rig that shows a little power and then folds back may have a protection fault rather than a dead PA.

5. SWR protection faults. Put the rig on a known-good dummy load. If it still folds back, the problem is inside the rig: the SWR bridge, the detector diodes, a leaky capacitor in the sensing circuit, or a bad low-pass filter relay. If it behaves on the dummy load, look at the antenna, coax and connectors. Always check this before concluding the finals are damaged.

6. Before condemning the finals. A DMM in diode mode can show a shorted junction or a dead short from drain to source, but a good reading doesn't prove the device is healthy. Look for the cause of the failure before replacing anything: high SWR, overdrive, a bias circuit fault, parasitic oscillation, or a supply spike. Fitting a new device into the same fault often destroys it as well. After the repair, set the idle current as the manual specifies and bring the power up gradually into a dummy load, using a current-limited supply if you have one.

7. Capacitors and contacts. Electrolytics in older gear dry out, and leaked electrolyte can eat nearby traces. Check the suspects with an ESR meter, or replace them with the same capacitance and an equal or higher voltage rating, using low-ESR types in switching supplies. Clean boards with isopropyl alcohol. Use contact cleaner on switches and relays sparingly. Over-spraying can push cleaner into places it shouldn't be.

8. Alignment is last. Don't touch the slugs until the rig is otherwise healthy. Use the service manual procedure, and note original positions before moving anything. You'll typically need a signal generator, a frequency counter and a power meter, plus a dummy load.

Caution if the rig has a mains power supply: the primary side is dangerous and shouldn't be probed casually. An isolation transformer and a lamp limiter are worth using for bench work.

What's your usual order? Do you check for supply ripple before anything else, or go straight to checking the RF path?

  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Agree with starting at power, and I'd add one thing: measure the rail at the point where it enters the board, not only at the connector. Contact resistance in the power plug or an internal fuse holder can drop a volt or more only when the transmitter is keyed. That gives you a rig that receives fine and seems to "lose power" on transmit, which looks like a weak PA but isn't one.

On the SWR protection point, if it folds back into a dummy load, I'd compare the forward and reflected detector voltages with the manual's expected values before replacing anything. A detector diode that has gone leaky or a drifted trimmer in the bridge can produce a false high-SWR reading. A scope helps here too. If the reflected voltage is present when it shouldn't be, you may be looking at RF getting where it shouldn't, such as a parasitic oscillation, rather than a real mismatch.

  • Administrators

One thing I'd add under noise: swap the supply for a battery, or any known linear supply, early on. If the noise disappears, you've isolated it to the supply or its wiring, and a lot of time is saved. If it stays, then it's either coming from the rig itself or arriving through the antenna and ground system. Digital noise from the rig's own CPU or display is another candidate, so check whether the noise changes with the display brightness or when you press buttons.

For capacitor replacement, my advice is to replace electrolytics in groups that share a function, such as the whole filter and decoupling stage of a supply, rather than a single part that tested badly. Meter readings on ESR can be misleading while the capacitor is in circuit. Also mind the orientation and the lead spacing, and use a heatsink or a low-temperature approach on small SMD pads. Lifted pads on a crowded board are harder to fix than a bad capacitor.

Does anyone have a preferred way of confirming a PA transistor is truly dead without desoldering it? Diode-mode checks seem to catch only the obvious short-circuit failures.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.