Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a homebrew QRP station from scratch: build order, test gear, and what to check before you key up

ci_cover.jpg

I'd like to compare notes on a sensible build ladder for someone who wants a real homebrew QRP station rather than a shelf of unfinished kits. The projects people usually start with cover very different skill levels, so the order matters.

Here is how I'd break it down. The Pixie and the Tuna Tin 2 are both simple CW transmitters, but they teach different things. A Pixie-style rig is a couple of transistors, a crystal, and an audio stage that doubles as the receiver. It is very cheap, but selectivity is poor and it hears both sides of zero beat, so it mostly teaches basic construction. The Tuna Tin 2 is a crystal-controlled 40 m CW transmitter of roughly a watt. It is a better lesson in oscillator and power amplifier stages, output matching, and harmonic filtering. Pair either with a decent direct conversion receiver and you have a working station on a very small budget.

The next step up is something like a BITX-style SSB transceiver. The BITX20 design uses bilateral amplifiers, diode ring mixers, and a crystal ladder filter, with the same stages used on both transmit and receive. The uBITX moves to a multiband layout with a synthesized VFO (Si5351) driven by a microcontroller board, plus switched low-pass filters. It is more approachable as a kit, but it is also easier to treat as a black box. I'd say check the output on a spectrum analyzer or a second receiver before assuming it's clean on every band.

The questions I'd like input on:

1) What is the minimum test gear you would insist on before building a transmitter? My starting list is a multimeter, a 50-ohm dummy load, an RF probe or a scope with a 10x probe, a frequency counter or a calibrated receiver, and a basic SWR bridge. Is a NanoVNA worth adding at the start for checking filters and antenna match, or can it wait?

2) For a first filter project, is a 5-element low-pass for one band the right place to start? How would you verify it, short of owning a spectrum analyzer?

3) For the power supply, I lean toward a regulated 12 V source with a fuse and a reverse-polarity diode, ideally with a current limit while you debug. Does that seem right for QRP, or is it overkill?

4) Soldering and toroids are where many kit builds go wrong: dry joints, enamel wire that was never properly stripped, and miscounted turns. What checks do you run before first power-up?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd put the dummy load and a way to see the RF at the very top of the list, ahead of an SWR bridge. Until the transmitter is happy into a resistive load, an antenna just adds variables. A dummy load made from several 1/2 W or 1 W carbon film resistors in parallel is fine at QRP levels. Ten 510-ohm resistors in parallel give 51 ohms, which is close enough, and the power is spread across the resistors. A diode RF probe on the multimeter then gives you relative output, and a scope gives you the waveform shape. That helps you spot an oscillator that is running but distorted, or a final stage that is clipping.

On the SWR bridge: a simple tandem-match or Bruene-style bridge is a good build in itself. Calibrate it on the dummy load first (reflected should read near zero), then try it with a known mismatch such as a 100-ohm resistor, where you expect roughly 2:1. A bridge that has never been checked against a known load is a guess.

For harmonics, a general-coverage receiver or an SDR tuned to the second and third harmonic frequencies, with attenuation between it and the transmitter, will tell you a lot. It won't replace proper measurement, but it will show you if a low-pass filter is doing nothing. A NanoVNA is useful for sweeping the filter on its own, before it ever goes into the transmitter, and for checking antenna match. I'd buy it second, after the dummy load and probe.

For toroids, keep a few T37-type cores and some scrap wire to practice on. Count turns by the number of times the wire passes through the center hole, not around the outside. Tin the enameled ends and check continuity before you install anything.

  • Moderators

One thing to know before the direct conversion receiver goes into the plan: it won't behave like a superhet. Because it has no IF filter, the audio stage does all the selectivity, so strong AM broadcast stations can break through, and you hear both sidebands at once. If the receiver breaks up near a strong station, a simple band-pass filter ahead of the mixer often makes a big difference, and so does a properly designed audio low-pass or CW filter. Hum and microphonics are common as well. If tapping the case produces noise, the mixer or a high-gain audio stage is probably picking up vibration or stray coupling.

The Pixie is fun for what it is, but it's also a good lesson in why a separate receiver and a proper TR scheme matter. A Tuna Tin 2 into a dummy load, monitored on a separate receiver, teaches more about keying and spectrum than most first kits. Listen for key clicks too. A hard-keyed oscillator or final can splatter, and simple RC shaping on the keying line is cheap to add.

On the power supply, yes to the fuse and the reverse-polarity protection, and I'd add one more thing: use a series resistor or a current-limited bench supply for first power-up on any new board. Raise the current gradually while watching for unexpected draw. For a keyer, an iambic keyer on a microcontroller or a simple kit is a low-risk project that gives you a fast result, and it's a gentle way to practice SMD soldering if it uses any. Check regulations for your country on spurious emissions before you go on air, since the limits vary.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.