Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24-hour EMCOMM field station: power budget, generator vs LiFePO4, noise control and a setup/teardown order

ci_cover.jpg

I'm sketching a standard field-station kit for a 24-hour EMCOMM deployment and want it critiqued before it gets written into a checklist. The assumptions: one HF rig (100 W class), one VHF/UHF mobile for local nets, a laptop for logging and digital modes, a few handheld chargers, and a tent or canopy for the operator. Nothing is planned beyond that, and no grid power is assumed.

Power first. Work in watt-hours so the numbers mean something. Wh = watts x hours, and amp-hours x 12.8 V gives a rough nominal capacity for a 12 V LiFePO4 pack. A 100 Ah pack is about 1280 Wh nominal. Assume 80 to 90 percent is usable, and leave margin for a BMS cutoff and for cold. A radio idling in receive might draw 1 to 2 A, but a 100 W HF rig can pull 20 A or more on transmit peaks. The honest way to budget is to estimate duty cycle: how many minutes per hour you actually transmit, how many hours the VHF rig sits on a net, and what the laptop and chargers pull continuously. Then add a buffer. Digital modes and long net-control stints push the duty cycle up fast.

The architecture I'm leaning toward: a LiFePO4 battery as the primary source, a small inverter generator as the recharge source rather than the station supply, and solar as a trickle top-up. The reasoning is that a battery-fed station has no generator inverter noise on the receive side, and the generator can run in bursts at a distance. The generator would charge through a proper charger or DC-DC supply while the station stays on battery, which also gives a clean changeover if the generator runs out of fuel or has to shut off.

Distribution: a fused main feed close to the battery terminal, a fuse block or Powerpole distribution panel, and every radio on its own fused branch. Standardize the connector orientation across the team so a borrowed cable can't reverse polarity. Wire gauge sized for the fuse rating, not just the radio's average draw.

Antennas and coax: a fiberglass mast guyed at multiple points, with an inverted-V or low dipole for NVIS on 80 or 40 m, plus a vertical or J-pole for VHF/UHF. A common-mode choke at the feedpoint and another at the radio. The coax run should be as short as practical on VHF/UHF, since small-diameter coax loses several dB per 100 ft at 146 MHz, while HF loss is minor for the lengths involved.

Questions: What's the biggest failure mode you plan for beyond the obvious? How do you prefer to handle grounding and lightning in the field? And is there anything in the setup order below that you would change? My draft order: site survey and wind/overhead hazard check, shelter, generator placement and CO safety, antenna and mast, coax and chokes, power distribution, radio checks, then logging.

  • Replies 2
  • Views 30
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Your architecture is sound, and I'd add details on the generator side. Carbon monoxide is the hazard people underestimate with a tent or canopy. Put the generator well away from the shelter, downwind, with the exhaust pointed away from anywhere people sit or sleep, and run a battery CO alarm inside the shelter anyway. Don't refuel a hot or running unit, and keep the fuel storage away from the generator and the operating position.

On grounding and bonding, read the generator manual rather than assuming. Many portable inverter generators have a floating neutral and a specific procedure if you're powering anything beyond direct plug-in loads. Don't improvise a backfeed into any building circuit. If it's powering extension cords, use a GFCI-protected arrangement and keep cords off the ground where water can pool.

On noise, I'd test before the deployment rather than during it. Run the generator-powered charger and any switching supplies at the planned distance and watch the S-meter or a noise floor measurement on the bands you intend to use. Switch-mode supplies, MPPT solar controllers and cheap USB chargers are all common noise sources, and the fix is usually distance plus ferrites or chokes on the offending lead, not a new antenna. Also treat a generator as a scheduled source: define the fuel and runtime plan so it doesn't quit during a net.

For lightning, there's no meaningful field grounding that makes an antenna safe in a thunderstorm. The plan should be a trigger: when a storm is approaching, stop transmitting, disconnect coax, and lower the mast if you can do it safely. A ground rod mostly helps with static and a reference point, not with protection from a strike.

  • Moderators

A few points on the battery and antenna side. First, LiFePO4 holds close to a flat voltage curve and then drops sharply near empty, so a voltage meter won't warn you well. Use a shunt-based battery monitor if you can, and know what your BMS does at its low-voltage cutoff. If it just disconnects, your station goes dark suddenly, so set an operational threshold well above that, say at a state of charge you define in the plan. Check each radio against the pack's actual voltage range, since a fully charged 12.8 V nominal pack sits near 13.3 to 14 V and some gear is more sensitive to the top end than the bottom.

Cold matters too. Many LiFePO4 cells shouldn't be charged below freezing unless the pack has low-temperature charge protection. If your solar or generator charging happens on a cold morning, confirm the specification for your battery first. Solar panels, for planning, usually deliver well below their nameplate rating once you account for angle, haze and controller losses, so size them as a top-up, not as the main supply, unless you've done the math for a real number of sun hours.

On the mast, the main rules are about the fall zone: keep the whole mast and antenna well clear of power lines, with a distance greater than the full height of the mast plus the wire span, and guy it for the expected wind rather than the forecast average. Stake guys visibly, or flag them, so people don't walk into them. For the teardown half of the checklist, I'd reverse the order: stop transmitting, shut down and disconnect radios, drop the antenna and mast, recover coax and guys, then power down the distribution, cool and pack the generator, and do a site sweep for stakes, cable ties and fuel residue. Add a final line to the list for photographing or documenting any gear that failed or misbehaved, so the next revision of the checklist improves.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.