Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a 100 W HF shack: how much does the radio matter versus power, tuner, filtering and bonding?

ci_cover.jpg

Spec-sheet comparisons of the IC-7300, IC-7610, FT-991A, FTDX10, TS-590SG, TS-890S and K3S dominate most rig discussions. A lot of the day-to-day noise, RFI and "why is my SWR jumping" trouble comes from everything around the transceiver, though. This thread is meant to separate those two things.

Here is a rough framing to push back on. The radios fall into loose groups:

- Direct-sampling SDR: IC-7300 and IC-7610. The 7610 adds a second receiver and a second ADC, plus separate RX antenna connections.
- Hybrid or narrowband SDR: FTDX10.
- Superhet with roofing filters: TS-590SG, TS-890S, K3S and FT-991A. The FT-991A also covers VHF/UHF.
- Portable or low power: KX3 (QRP class) and Xiegu G90 (about 20 W, built-in ATU).

Which of these gets better results depends heavily on the band conditions and the neighbourhood noise floor, and on whether you run an amplifier or share a site with other stations.

Questions for discussion:

1. For a 100 W rig, what are sensible minimums for the power supply (continuous current rating, regulation, noise)?
2. When does an external tuner help, and when does it just hide a bad antenna system?
3. When are band-pass filters worth buying, and when should you reach for the attenuator or preamp settings instead?
4. What does a sensible bonding and grounding scheme look like, separating safety and lightning protection from RF behaviour?
5. Any layout rules that prevent problems before they start?

  • Replies 2
  • Views 25
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the power supply: a 100 W HF rig on SSB or CW usually peaks around 20 A or a bit more at 13.8 V. A "30 A" supply is a reasonable choice, but check whether that is continuous or peak and whether voltage holds up under a keyed carrier. Digital modes and long CW dashes load it harder than voice does. Modern switching supplies can be quiet or terrible. If you hear a comb of birdies or a raised noise floor that changes when you unplug the supply, the supply is a suspect. Ferrites on the DC leads and a shorter run often help. A linear supply is the heavier, quieter option, but it is not the only way to a clean receiver.

Voltage drop is often overlooked. Use an adequate wire gauge for the run, keep it short, and use properly crimped connectors (Powerpole-style or similar) rather than relying on the thin cable that ships with the radio for extension runs. If the rig shuts down or output sags on peaks, measure at the radio's connector while transmitting, not at the supply.

For bonding, the safety side is the AC mains equipment ground, which is separate from "RF ground." A ground rod at the operating position does little for RF, and a long wire to it can become part of the antenna. The practical aim is to tie equipment chassis together with short, wide conductors (braid or strap) so there are no big potential differences between boxes. Add a common-mode choke on the coax at the shack entry or the feedpoint, depending on where the common-mode current is being picked up. Lightning protection is its own subject: entry-point bonding, surge protection and tie-in to the electrical service ground. Check your local electrical code, and consider a qualified electrician for anything touching the service panel.

  • Moderators

On the tuner and filtering questions, a tuner makes the radio see 50 ohms, but it does nothing about loss in the feedline caused by high SWR. A built-in ATU such as the ones in the G90, IC-7300 or IC-7610 handles modest mismatches. A badly mismatched antenna on coax can waste a lot of power in the line, and a tuner at the shack end will not fix that. If you run a multiband wire fed with ladder line, a tuner suited to balanced feeders is the intended solution, and that is a different design choice from a mismatched coax-fed antenna. With an amplifier, tune up at low drive with the tuner first, then bring up the amp, and make sure the tuner is rated for the power you intend to run.

Band-pass filters are mainly for situations where a strong signal on another band reaches the front end, for example multi-transmitter setups, SO2R, or a close neighbour's transmitter. In-band overload (a strong station a few kHz away) is not something a BPF solves. Those cases are handled by the radio's roofing filter and AGC behaviour, and by the attenuator, preamp and bandwidth settings. If you do add BPFs, check the power rating, the insertion loss and whether they sit in the transmit path or only on receive.

The superhet-vs-SDR argument tends to sound more decisive than it is on typical antennas. Receiver dynamic range matters most with strong local signals or crowded contest conditions. For a quiet-location home station with a modest antenna, the antenna and noise environment will often limit you before the radio does. A radio-by-radio ranking is probably less useful than asking what your limiting factor is: noise floor, adjacent strong signals, RFI in the shack, or TX power and antenna efficiency.

On layout, keep RF feedlines apart from USB, audio and computer cables, and cross them at right angles where you must. Put ferrites on USB and CAT cables. Mind ventilation for the amplifier and supply. Leave room to reach the back of the gear, because most troubleshooting ends up back there.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.