Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Homebrew build order: receiver first, or go straight to a QRP transmitter? What test gear actually matters?

ci_cover.jpg

Say you want to move from kits to designing and building your own gear, starting from a modest parts drawer and a multimeter. Projects like a crystal set, a Pixie, a Tuna Tin 2, a direct conversion receiver, a BITX or uBITX, and the accessories around them (low-pass filters, SWR bridge, keyer, power supply) can be built in many different orders. Some orders teach a lot more than others, and some leave you with a transmitter you can't safely or legally check.

Here is a build order that seems to make sense, and I'd like to hear where people disagree.

1. Receiver before transmitter. A direct conversion (DC) receiver for 40 m or 80 m is a good first RF project. It has a handful of stages: bandpass filter, diode-ring or active mixer, VFO or crystal-controlled LO, and a high-gain audio chain, often with an LM386 or an op-amp preamp in front of it. It teaches layout, grounding, VFO stability and audio gain without a transmit chain that could emit spurs. The usual DC problems are AM broadcast breakthrough (fixed with input selectivity), hum and microphonics, and the lack of sideband rejection, so you hear both sides of zero beat.

2. A simple CW transmitter next. The Tuna Tin 2 (Doug DeMaw, W1FB) is a one-transistor, crystal-controlled CW transmitter with an output of a few hundred milliwatts. It is a good lesson in output networks and in why a low-pass filter is not optional. A Pixie-style transceiver is simpler still, and its final transistor doubles as the receive detector. That is fun, but its receiver performance is poor, so treat it as a learning exercise rather than a station.

3. Then an SSB transceiver. BITX-family designs reuse the same filter and mixer stages for both receive and transmit with bilateral amplifiers. That makes them excellent for learning how a superhet works, and it makes alignment trickier. The uBITX takes the modular approach, with a microcontroller-driven Si5351 synthesizer, a wideband design and relay-switched filters. Whatever the platform, harmonics and spurs on the upper bands are worth checking before you put it on the air.

4. Accessories along the way. The low-pass filter, a dummy load, a tandem-match or resistive-bridge SWR meter and a simple bench supply are all worth building early, because they let you check the later projects safely.

Questions for the thread: Would you reorder this? What is the minimum test equipment you'd want before building your first transmitter? And what do you do for harmonic checks if you don't have a spectrum analyzer?

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd keep the receiver first, with one tweak: build the audio chain and the LO as separate boards or at least separate sections, and test each on its own. A DC receiver is mostly a story about gain distribution. With the mixer and the audio amp together on a single piece of copperclad, you can't tell whether the hiss is the mixer, the preamp or the layout.

A few things commonly cause grief in DC receivers:

First, LO leakage to the antenna. If the LO is strong and the mixer is not well balanced, the LO radiates and also produces DC offsets at the mixer output that get amplified by the audio chain. A balanced mixer (diode ring, or an SA612-type double-balanced mixer) and a bit of buffering help.

Second, AM broadcast stations overloading the first stage. A simple bandpass filter in front of the mixer, rather than just an untuned antenna connection, makes a very noticeable difference on a long wire.

Third, the image problem. A DC receiver has no sideband selection, so both sides of zero beat come through. You can accept it for CW, or build a phasing type with a 90-degree audio network if you want a quieter band and better single-signal reception. That is a good second receiver project.

For the transmit side, a low-pass filter should be on your list as soon as you pick any transmitter stage, even a Tuna Tin 2. Square-wave-ish switching stages are rich in harmonics, and the usual advice is a 5-element Chebyshev design for the band. Wind the toroids carefully and verify them with a VNA or at least an RF probe and a signal source.

  • Moderators

On the test equipment question, here is what tends to give the most value for the money, roughly in order:

A decent multimeter and a current-limited bench supply (or at least a fuse and series resistor while you bring up a new board). Many first-time failures are a reversed electrolytic or a solder bridge, and current limiting turns them into non-events.

A dummy load, so you never have to test a transmitter into an antenna. A resistive load built from non-inductive resistors in parallel is fine at QRP power levels. Keep in mind that resistors heat up, so don't leave a 5 W transmitter keyed down into a few small 1/4 W parts.

An RF probe for your multimeter, or a simple diode detector. It will not give you exact power, but it shows you whether a stage is working and lets you peak a tuned circuit.

An oscilloscope with a bandwidth well above your operating frequency, if you can afford one. Use it with a 50-ohm termination on the dummy load to estimate power with P = Vrms² / R, taking Vrms = Vpp / (2 × 1.414). Be sure about the probe's compensation and the scope's input impedance before trusting any number.

A NanoVNA or similar for filters, antennas and SWR checks. It is excellent for confirming that your low-pass filter's cutoff and passband loss are where they should be, and it can double as an SWR meter for the dummy load.

For harmonics, a spectrum analyzer is ideal, but if you do not have one, you can compare the transmitter's output before and after the filter with a receiver that has an S-meter, or borrow time on a club's analyzer. Many licensing regimes set limits on spurious emissions, so check your local rules rather than guessing.

On the uBITX in particular, it is a kit-based platform and a good one for learning, but the stock design is known in the community for spurious output on some bands, so verifying the filter set and output is a worthwhile step, not an optional one.

For soldering, a temperature-controlled iron, flux, a clean tip and good lighting matter more than brand. Tin the tip, heat both the pad and the lead, then feed solder to the joint. For hand-built RF circuits, dead-bug or Manhattan construction on copperclad is fine, as long as ground connections are short.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.