Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

From-scratch wire antenna build: what actually matters in wire, insulators, chokes, ladder line and modeling?

ci_cover.jpg

Starting a thread for the homebrew side of antennas: dipoles, wire verticals, inverted Ls, doublets fed with ladder line, and the occasional trap design. The goal is to sort out which details change results and which are mostly folklore. Corrections welcome.

Start with length. The usual half-wave formula is 468 / f(MHz) feet, or 142.6 / f(MHz) meters. For 7.1 MHz that gives about 65.9 ft (20.1 m) overall. Treat it as a starting point only. Height above ground, nearby conductors, wire insulation and end effects all move resonance, and insulated wire typically ends up a few percent shorter than bare wire. Cut long, fold the excess back at the ends, and trim in small steps. The same applies to a quarter-wave vertical: 234 / f(MHz) feet, so about 16.5 ft (5 m) for 14.2 MHz, before any adjustment for the feedpoint and the radial system.

On wire gauge, the loss difference between 12, 14 and 16 AWG in a resonant dipole is tiny compared to ground loss, feedline loss or common-mode current. Gauge mostly decides mechanical survival. Hard-drawn copper holds up but can kink and break. Copperweld (steel core, copper cladding) stretches less over long spans, and stranded insulated wire is easier to handle and tolerates fatigue better. Thinner wire is fine for portable or short-term use. For a permanent long span, strength and stretch matter more than conductor resistance. Stretch is also why a dipole that was resonant in spring may not be in summer.

Insulators and supports are where many builds fail first. Use UV-stable plastic, glazed ceramic or similar for end and center insulators, and avoid hardware-store rope that rots or stretches. Polyester or other UV-resistant cordage is the usual choice. Wire passing through a hole in an insulator concentrates fatigue at the bend, so use a wrapped or crimped loop. At the center, the coax needs strain relief so the weight pulls on the insulator or support and not on the solder joint or connector. Seal the connection, and give the cable a drip loop so water does not run into the coax. For end supports that move in the wind, a pulley with a counterweight or a length of bungee keeps tension from changing constantly.

The question I would most like to get into: how much of the feedline and balun side is essential, and how much can wait? A coax-fed dipole radiates better and reads more consistently with a 1:1 current balun or choke at the feedpoint. Ladder line avoids most feedline loss on mismatched multiband doublets, but it needs a tuner that can handle the mismatch and a balanced or balun-isolated connection at the tuner. And whenever the measured SWR changes when you move or shorten the coax, common-mode current is the likely cause.

What are people using for the center support, feed arrangement and checking, and where do you draw the line between a quick field antenna and a build that is meant to last?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the feedline side, think about what the choke has to accomplish. It should put enough common-mode impedance on the outside of the coax to keep the shield from acting as part of the antenna. A rough target is several hundred ohms at minimum and ideally in the kilohm range on the bands you use. A stack of suitable ferrite cores (the mix matters, and 31 and 43 are the usual HF choices) or a coiled-coax choke can do it, but a choke that is excellent on 40 m can be weak on 10 m. Check the choke impedance against the band instead of assuming it works everywhere. Winding turns of the coax itself through cores works, and so does coiling the cable to form an inductor with some self-resonance. Neither is universally better, because the answer depends on the core, the cable and the bands.

For ladder line, the main rules are to keep it clear of metal and gutters, avoid running it parallel to conductors for long distances, and keep the twist or bend radius sensible. Common-mode current on a ladder line system usually shows up as RF in the shack or a tuner setting that changes when you touch things. A 4:1 current balun at the tuner end is an option, but a balanced tuner avoids the balun entirely, and a well-matched balun in the middle of a mismatched system can run hot. I would not reach for a 4:1 and call it done without checking what impedance it actually sees.

For measuring, an antenna analyzer or a NanoVNA at the feedpoint tells you more than a SWR meter at the radio. Calibrate at the connector you are using (open, short, load) and keep power low. Feedline loss lowers the SWR you read at the radio, so a good number there does not prove the antenna is good. Minimum SWR is also not exactly the same as resonance. Resonance is where the reactance crosses zero, and the two frequencies can be a little apart, especially on wide-bandwidth designs.

  • Moderators

Modeling is worth doing before you cut wire, as long as you know what the model cannot tell you. With EZNEC (NEC-based) or MMANA-GAL (MININEC-based), the first checks are segmentation and junction geometry. Segments should be short relative to wavelength, and segment lengths should be reasonably similar where wires meet, particularly at the feedpoint and where wires bend. Sloping wires, inverted Vs and wires close to ground need more care. It also helps to run an average gain test where the program provides one, because a lossless free-space model should come out near 0 dBi. If it does not, the geometry or segmentation is suspect.

Models are only as good as the ground assumption. Ground conductivity and permittivity change low-height patterns and impedance noticeably, and neither program knows your actual soil. So a model is better for comparing options (inverted V against flat top, 2 versus 4 elevated radials, trap placement) than for predicting the exact SWR you will see. The velocity factor of insulation and the capacitive loading from supports, rope and nearby trees will not be captured unless you add them.

For verticals, radials matter more than almost anything else. Ground-mounted radials need a lot of wire, since the number of radials and how long they are both affect ground loss. Elevated resonant radials can work with far fewer wires. Drooping them down at roughly 45 degrees also moves the feed impedance upward toward 50 ohms, instead of the lower value you see with horizontal radials. A choke at the base is still useful, because the feedline can act as another radial.

Traps trade simplicity for loss and bandwidth. In a dual-band trap dipole, the trap is parallel resonant at the upper band and isolates the outer wire, while on the lower band it acts as inductive loading and makes the antenna shorter than a plain dipole. Capacitor voltage rating, coil Q and weatherproofing all matter, and you should measure the trap's resonant frequency on the bench before installing it. A pair of plain dipoles fed from one point, or a fan dipole, is a simpler alternative for two or three bands, though the interaction between wires will shift lengths.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.