Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Band plans vs. FCC rules: how do you decide where to operate from 160 m through 33 cm, and how close to the band edge is safe?

ci_cover.jpg

Question for the group, especially anyone who explains this to newly licensed or newly upgraded operators. The ARRL band plan, the FCC privilege tables and the habits you hear on the air don't always line up, so which one do you follow for what?

Here is what I'm trying to sort out:

1. Which parts are law (Part 97) and which are voluntary band plan or convention? Examples are the CW/data versus phone split, FT8 watering holes, and DX windows.

2. How do you work out a safe frequency near a band edge, such as the bottom of the General phone segment on 20 m or the top of 75 m, when the dial reads the carrier frequency but the signal occupies bandwidth on one side?

3. What are the simplex calling frequencies on 6 m, 2 m, 70 cm and 33 cm, and how are they meant to be used?

4. How do 60 m channels differ from every other HF band?

5. If you operate while traveling, or listen to stations in other countries, how much do international allocations change the picture?

I'd rather get the reasoning than a memorized chart, since the charts change.

  • Replies 2
  • Views 23
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the split between rules and plans. Part 97 is the regulation. It defines which bands and sub-bands each license class may use, which emission types are allowed where, and the power limits. The ARRL band plan is a voluntary coordination document. It suggests where weak-signal work, beacons, digital modes, repeaters and so on should live so they don't step on each other. Violating the band plan isn't a federal violation, but it's how you end up in an interference argument. Ignoring a Part 97 boundary is a violation, and you're responsible for it.

For HF, the usual US pattern is CW and narrow digital modes in the bottom part of each band, with phone in the upper part. The General class phone segments start above the Extra-only portions on bands like 80, 40, 20 and 15 m. Tables change, so check the current Part 97.301 through 97.305 and the current ARRL chart. Don't rely on a memory of Novice-era or pre-2000s charts. Technician HF privileges are limited: CW on 80, 40 and 15 m, and CW, RTTY/data and phone on a segment of 10 m. General adds large chunks of every HF band, including 160 m, and Extra gets the full allocations. The WARC bands (30, 17 and 12 m) have no phone on 30 m, and by convention contests stay off all three.

On digital, the FT8 and FT4 frequencies (for example, around 14.074 MHz on 20 m and 7.074 MHz on 40 m) are conventions, not regulations. They exist so everyone is in the same place. Rule changes to data limits on HF have been in the news, so check the current text before assuming old baud-rate limits still apply.

On band edges, think about which sideband you're using. If you're on USB, as is the convention above 10 MHz, the signal extends upward from the dial frequency. At the bottom of a phone segment, such as the General 20 m phone edge, being right at the limit is fine, though leaving some margin for dial calibration is wise. At the top of a band you must keep the whole signal inside, including any splatter, so stay a few kHz down. On LSB, as is the convention below 10 MHz, the signal extends downward from the dial, so the lower edge needs the margin instead. A typical SSB signal is about 2.4 to 3 kHz wide, and a transceiver with a poorly calibrated display or an overdriven audio chain can spread further. Spurious or over-processed audio is why many operators keep 3 kHz or more of margin at the edge. That margin is not a rule, just good practice.

60 m is different from the other HF bands. It's channelized, not a continuous segment, and in the US it has five channels with USB specified. The commonly listed dial frequencies are 5330.5, 5346.5, 5357.0, 5371.5 and 5403.5 kHz, with center frequencies 1.5 kHz above each. The power limit is expressed as effective radiated power, not as a PEP figure at the transmitter. The FCC rules for this band have been revised before, and new allocations from international conferences may change things, so check the current Part 97.303 text before operating.

  • Administrators

Adding the VHF/UHF part and the international side, since those answers are mostly about conventions.

6 m (50 to 54 MHz) has distinct sub-bands in the ARRL plan. The bottom is CW-only weak-signal work and beacons. The SSB calling frequency is 50.125 MHz, and 50.313 MHz is where FT8 is commonly found. The national FM simplex calling frequency is 52.525 MHz. The idea of a calling frequency is that you make contact there and then move off to another frequency to talk, so you don't tie it up with a long conversation.

On 2 m (144 to 148 MHz), 146.520 MHz is the national FM simplex calling frequency, and the plan reserves the surrounding region for FM simplex. 144.200 MHz is the SSB calling frequency, and weak-signal work (CW, SSB, EME) is in the lower part of the band, with repeaters in the segments above that. APRS in North America is on 144.390 MHz. On 70 cm (420 to 450 MHz in the US), 446.000 MHz is the national FM simplex calling frequency, and 432.100 MHz is the usual weak-signal calling frequency. Repeater pairs are in the 442 to 445 and 447 to 450 MHz regions, subject to local coordination. Local frequency coordinators can make exceptions, so a regional repeater map might not match the national plan. Technician and above have access to all of these in the US.

33 cm (902 to 928 MHz) is a different kind of band. Amateur use there is secondary, shared with other services including unlicensed Part 15 devices, so local noise can be significant. It is also allocated to amateurs in ITU Region 2 only, so it isn't available in Europe or Africa. The ARRL plan puts weak-signal operation near 902 to 903 MHz, but I don't remember the exact calling frequencies reliably, so check the current plan rather than relying on a number from a forum post.

Internationally, the ITU divides the world into three regions, and allocations differ. A few examples: 40 m is 7.0 to 7.3 MHz in Region 2 (the Americas) but 7.0 to 7.2 MHz in Region 1. 80 m runs 3.5 to 4.0 MHz in Region 2 and 3.5 to 3.8 MHz in much of Region 1. 70 cm is 430 to 440 MHz in Region 1 but 420 to 450 MHz in the US portion of Region 2. 6 m is not available in every country, and 60 m access varies widely by country and by license class. When you listen to a station abroad, they may be legally transmitting on a frequency your license wouldn't permit, and the reverse applies when you travel. If you plan to operate in another country, look into its reciprocal licensing arrangement and follow the local rules for bands, power and modes. Your US privileges don't go with you.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.