Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio setup: mic gain, ALC, compression and bandwidth for clean signals and weak-signal work

ci_cover.jpg

Many SSB reports come down to the same few settings: mic gain too high, processor stacked on top of that, and a transmit bandwidth wider than the band needs. Here is a sequence for setting up a clean, readable signal, followed by some questions I would like others to weigh in on.

1. Start with the microphone and how you use it. Voice intelligibility on SSB lives mostly between roughly 300 Hz and 2.7 kHz. A mic with a strong, even response in that range usually beats a hi-fi mic with a lot of low-end energy. Keep a consistent distance, typically a few centimeters, and talk slightly across the capsule rather than straight into it to reduce plosives. A foam windscreen or pop filter is cheap and useful. Room echo matters more than people expect, because a hard-walled shack gets picked up and turns into mush after compression.

2. Set mic gain by the ALC, not by feel. ALC (automatic level control) is a safety net that pulls the gain down when the signal gets too large for the final stage. It is not meant to be your main audio control. With the processor off, speak at normal volume and adjust mic gain so the ALC meter just touches its allowed zone on voice peaks, and does not sit pinned. If the ALC is deeply into its range, you get flat-topping, distortion and splatter, and the other station may hear a wide, raspy signal even though your meter looks strong. Also check the manual for your radio, since ALC metering and recommended ranges vary by model. If you run an external amplifier, ALC voltage from the amp is a separate adjustment and should not be pushed.

3. Add compression gradually. A speech processor raises average power relative to peak power, which helps in noise and QSB. The trade-off is that it also raises background noise and room sound, and it adds distortion when pushed. A reasonable method is to turn it on and increase the compression level in small steps while watching the compression meter if your radio has one. A few dB is often enough. Several radios have processor levels where intelligibility peaks and then drops quickly. Re-set mic gain after turning the processor on, because they interact.

4. Use the monitor, but know what it tells you. The TX monitor is handy for hearing your own mic, EQ and processor effects, preferably in headphones with the volume kept low to avoid feedback. On most radios it samples audio inside the transmit chain, so it does not necessarily reveal RF problems such as overdrive of the PA or an amplifier. For that, you need an independent receiver, an SDR monitoring your own signal at a safe distance, or honest reports from other stations. Be careful with the second approach: avoid overloading a receiver with a nearby transmitter.

5. Equalizer: small cuts first. Cutting low frequencies, often below 150 to 300 Hz, removes boominess and saves power for the part of the spectrum that carries consonants. A gentle presence boost around 2 to 3 kHz can help, but heavy boosts make audio harsh and emphasize sibilance. Most radios let you adjust TX bandwidth. Setting something near 2.4 to 2.7 kHz is common. A narrower transmit passband can help weak-signal contacts, while a wider one sounds more natural during casual ragchews on a quiet band. Crowded bands and contests favor the narrower option for the sake of your neighbors.

6. Sideband convention. By amateur convention, LSB is used on 160, 80 and 40 meters, and USB on 20 meters and up. 60 meters is a special case, and in some places, USB is required on channelized allocations. Follow your local rules and band plans. 30 meters is mostly CW and digital.

7. Receiving weak stations and DX. On receive, a 2.4 kHz filter is a good default. For weak stations with adjacent QRM, try a narrower setting around 1.8 to 2.1 kHz, or shift the passband and IF shift/twin PBT if the radio supports it. Use the RF gain, attenuator and preamp appropriately: a preamp does not help on lower bands where atmospheric noise is already above the receiver noise floor, and it can hurt through overload. Noise reduction can help, but heavy settings make speech sound watery and can cover the very signal you are trying to copy. AGC speed matters too; slow AGC is smoother, but fast AGC may help in dense signals or when a strong neighbor desensitizes the receiver.

8. Operating technique counts as much as settings. Speak at a steady pace, give your call clearly, and use standard phonetics when conditions are poor. Do not talk faster just because the band is loud. When working DX, resist adding more compression or power if it makes your signal wider and messier. Often the best fix is a better antenna, or less noise at your location.

Questions for the thread: what ALC and compression settings are you actually using with your current rig? Do you leave the equalizer flat, or do you cut the lows? And how do you check your own signal for splatter before you call a rare station?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One thing I would add to the ALC point is that the setting depends on your whole chain. If you run an amplifier, set your drive power first so the amp is not pushed beyond its rating, then adjust mic gain and processor around that. Many clean-signal problems show up only when an amplifier is added, because a transceiver that sounds fine on 100 W can distort badly once its output drives a linear past its comfortable level. If your radio has an adjustable output limit for the amp, use it rather than trying to control power with mic gain alone.

For checking splatter, a second receiver or SDR showing your signal on a spectrum display is useful, as long as it is protected from the transmitter. Compare your signal width with a clean station on a similar band. If your signal shows sharp skirts a few kHz away when you speak loudly, back off the mic gain and processor before blaming the band.

  • Moderators

On the equalizer, I would treat 'flat' as a starting point rather than a rule. Voices differ, and so do microphones. A cut in the low end often helps with a desk mic that picks up table thumps and boomy room sound. A headset mic may already be thin, so extra low-cut could leave the voice sounding tinny. Record a short test with your radio's built-in recorder, if it has one, or listen through a monitor receiver, then adjust one control at a time. It is easy to fix several things at once and not know which change helped.

For weak-signal and DX work, I would separate two goals: sounding natural and being easy to copy through noise. For a pileup or poor path, a slightly narrower TX bandwidth with modest compression often works better than a full-range, nicely shaped voice. When conditions are good and you are not competing with others, go back to wider, lower-compression audio. Rather than keeping one profile for everything, store a 'DX' and a 'ragchew' memory if your radio supports it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.