Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building out an HF shack around a 100 W rig: what to sort out first (power, tuner, filters, bonding)?

ci_cover.jpg

This thread is for the parts of an HF station that tend to matter more than the radio itself. The rigs people usually compare are the IC-7300 and IC-7610, the FT-991A and FTDX10, the TS-590SG and TS-890S, the K3S and KX3, and the G90. Whichever you pick, the same questions come up when you put it in a shack: what powers it, how it meets the antenna, what keeps the neighbouring transmitter out of the receiver, and how everything is bonded.

Here is a rough order of priorities to argue about.

1. Antenna system first. A 100 W rig into an efficient, resonant antenna and low-loss feedline beats a more expensive rig into a compromised one. An internal ATU on the IC-7300, IC-7610, FT-991A, FTDX10, TS-890S or G90 presents 50 ohms to the transmitter, but it does nothing about loss in the feedline between the rig and the antenna. With a high SWR on a long run of coax, that loss is the real cost. A tuner at the feedpoint, or a balanced line with a balanced tuner, is a different thing from a tuner at the desk.

2. Power supply. A 100 W HF rig typically wants around 20 to 22 A at 13.8 V on transmit peaks, so a 25 to 30 A continuous supply leaves comfortable margin. Voltage sag under load shows up as splatter or ALC weirdness and is often blamed on the radio. Use short, adequately sized DC cables, fuse the positive lead close to the source, and check the supply for noise on the bands you care about. The KX3 and G90 are in a different class: low current, and often run from batteries.

3. Receive front end. Strong signals on other bands are the usual problem, particularly with a second transmitter nearby (contest multi-op, SO2R, or a neighbour's station). The IC-7610, K3S and TS-890S are generally considered strong on dynamic range, and the FTDX10 and TS-590SG have a good reputation as well. Even so, a band-pass filter is worth considering when two stations share a site. Check that it is rated for the power passing through it, and expect some insertion loss.

4. Grounding and bonding. Most arguments start here, so I'll separate the three jobs people mix up: electrical safety (mains earth), lightning protection (an entrance panel, with rods bonded to the service ground), and RF behaviour (common-mode chokes, short bonds between equipment chassis). A bus bar tying the rig, tuner, amplifier and supply together with short, wide strap is a common approach. Check your local electrical code, because it governs how ground rods and the house ground must be connected.

Questions to get started: what is the first thing you would add to a stock IC-7300 or FT-991A shack, and when does an amplifier make sense compared with a better antenna? Where do you put the tuner and the choke?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the power supply point, check what the amplifier needs before buying the supply for the rig. A 500 to 600 W class solid-state 13.8 V amp draws far more current than any 100 W transceiver, and most amplifiers in that class come with their own supply or a specific recommendation for one. Match the cable gauge and fusing to the amp's data sheet, not to the radio's. Also, the supply should be sized for continuous duty, not just SSB peaks. Digital modes and CW at full power are far kinder to the voltage regulation of a 30 A supply than a 20 A one at its limit.

I'd also be careful with the idea that an internal ATU can substitute for fixing the antenna. The built-in tuners on the IC-7300, IC-7610, FT-991A, FTDX10 and TS-890S have limited match ranges, so they are best for small SWR bumps across a band. The G90's wider-range tuner can force a match on something awkward, but a match at the radio end does not recover power lost in the line. If the SWR is high at the antenna, put the tuner there or switch to a balanced feedline and a balanced tuner. Whichever tuner you use, retune at low power after any change, and avoid hot-switching an external tuner or antenna switch.

  • Moderators

I'd tone down the idea that a band-pass filter is the first purchase. For a single-operator station with one transmitter, it usually isn't. A BPF belongs in the chain when a transmitter on another band is close enough to overload the receiver, which is typical for SO2R and multi-op setups. For ordinary use, the common wins are a good low-pass filter for harmonics on the amplifier output, and a separate receive antenna, which the IC-7610 and K3S both make easy with their RX antenna connections. On the IC-7610 you can also make use of the second receiver for diversity-style listening.

On bonding, I'd say the real goal is predictable behaviour rather than a magic ground. Tie the chassis together with short, wide strap. Run the coax through an entrance panel, with arrestors bonded to the same system as the house ground. Then deal with common-mode current, which is usually what causes RF in the shack. A choke on the coax at the radio and again at the entrance often does more for RFI than adding ground rods. USB and CAT cables are another common path, so use ferrites on them. If you get hum or noise on a digital interface, a ground loop through the computer and the rig is a likely cause, and USB isolation can help.

Lightning protection is the one place I'd stay conservative. An arrestor does not make a station safe in a direct strike. The most dependable protection is to disconnect and move the coax outside the building when the station is not in use. Check local codes for how the entrance ground has to be bonded to the mains ground.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.