Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio setup: mic gain, ALC, processor and bandwidth for a clean signal that still gets through

ci_cover.jpg

A lot of SSB audio problems come from stacking settings that each make sense alone: a hot mic gain, the processor turned up "for punch", a boosted EQ, and a wide transmit bandwidth. The result is a signal that sounds loud in the shack and splatters or distorts on the air. I'd like to collect a sensible order of operations for setting up a voice chain, then hear where people disagree.

Start with the microphone and the room. Mic placement matters more than any menu item. Most dynamic and headset mics work best a couple of finger-widths from the lips, speaking slightly across the capsule rather than straight into it to reduce plosives. A foam windscreen or pop filter helps. Hard walls and a bare desk add reflections that a processor will make worse, since compression raises the level of whatever is quiet, including room sound and fan noise. Pick one mic position and keep it consistent so your gain settings stay valid.

Set mic gain with the processor off first. Speak at normal contest or DX volume and watch the ALC meter. The usual guidance is that ALC should barely move on voice peaks, or stay within the rig's marked ALC zone. If it is pinned or constantly slamming, the audio is being squashed after the mic stage in a way you didn't choose, and that is often where flat-topping and splatter begin. Check the manual, because meter scales and ALC behavior differ between radios. Also keep in mind that ALC is a protection circuit, not a compressor you should lean on.

Add the speech processor sparingly. Rigs implement this as AF compression, RF clipping, or both. A small amount, often just a few dB of compression on the rig's compression meter if it has one, raises average power relative to peak power and can help a weak signal stay readable. Past that, you get a fatigue-inducing sound, more background noise, and more distortion products that spread outside your passband. Re-check ALC after enabling it, since many radios need mic gain reduced when the processor is on.

Use the monitor. Monitor level lets you hear what your audio chain is doing. Use headphones so it doesn't feed back into the mic. A monitor won't tell you exactly how you sound a thousand miles away, but it will reveal harshness, pumping, and obvious distortion. A local receiver, an SDR, or a trusted station nearby can give you an independent check of both audio and occupied bandwidth.

Equalizer and transmit bandwidth. Trimming low frequencies below roughly 200 Hz usually does more good than boosting highs, because it removes thumps and room rumble that consume power without helping intelligibility. A mild presence lift in the 1.5 to 3 kHz area can improve articulation, but pushing it makes sibilance and splatter worse. Many modern rigs let you narrow the transmit passband, for example something near 300 to 2700 Hz. A narrower signal concentrates power where the information is and takes up less space on a crowded band. A wide setting can sound great on a local rag chew but is poor etiquette when the band is full.

Sideband convention. The common convention is LSB below 10 MHz and USB above it. The 60 meter band is the usual exception, where USB is used in many places, so check the rules for your region. Using the wrong sideband isn't a fault in your audio, but it makes you hard to copy and unhelpful to others.

On receive. A 2.4 kHz filter is a good general default for SSB. For weak stations or QRM, narrowing to about 1.8 to 2.1 kHz, shifting the passband, or using the notch can help. Noise reduction can help or hurt: moderate settings can reduce fatigue, while aggressive ones create artifacts that mask weak speech. Experiment with AGC speed, preamp, and attenuator. On the lower bands atmospheric noise often dominates, so a preamp may add nothing but more noise.

Which part of the chain do you adjust first, and do you trust meters or recordings and reports more for dialing in your audio?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd put a recording check ahead of the meters. ALC and compression meters are only a proxy; the rig can show healthy levels while the audio still sounds boxy because of a poorly placed mic or a harsh EQ curve. Record your transmission into a dummy load or listen via a second receiver and compare it against a station you know sounds good. Then you're adjusting for the sound, not for a needle position.

One caution on the processor: the right amount depends on conditions. In a quiet band opening, you may not need any, and the unprocessed audio will be more natural. When the band is noisy and the other station is hunting for you, a little compression can help, but there is a point where more processing only makes you louder in the shack and not any more readable at the far end. If the other operator asks you to repeat something, turning the processor up is often the wrong response; slower, clearer speech and a good callsign delivery usually do more.

  • Moderators

For DX and pileups, the setup matters less than technique. Listen long enough to understand how the DX station is working: split operation, call areas, or a net-style list. Then give your callsign once or twice, using standard phonetics, instead of long strings of repeated calls. If you're running an amplifier, keep drive within the linear range and check ALC from the amp too, since clean audio into a clipped amp still splatters and annoys neighbors on the band.

On the receive side for weak signals, I'd narrow the filter before reaching for NR. Dropping from 2.4 kHz to something in the 1.8 to 2.1 kHz range often removes enough adjacent noise to make speech copyable without the underwater artifacts that heavy DSP noise reduction can add. Slow AGC and manual RF gain also make a big difference when a weak signal sits beside a strong one. Make one change at a time so you can tell what helped.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.