Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting the most out of 5 watts: rigs, antennas, power and where to find other QRP stations

ci_cover.jpg

Starting a general QRP thread to collect practical advice in one place. QRP is usually taken as 5 W output on CW, and many operators treat 5 W as the working limit on SSB too, though some contests allow a higher PEP figure for phone. If you plan to chase QRP-ARCI events or awards, check the current rules for the exact power definition.

The efficiency argument. Going from 100 W to 5 W is about 13 dB, a little over two S-units on the far end's meter. That sounds like a lot, but a decent antenna change can recover several dB, and a CW receiver with a narrow filter pulls signals out of noise that SSB can't. Most QRP success comes from the antenna, band choice, time of day and operating technique, not from the rig.

Rigs people commonly discuss:

Elecraft KX2 and KX3: all-mode, multiband, built-in keyer, optional internal ATU and battery. The KX2 is smaller and runs up to about 10 W, and the KX3 goes up to about 15 W. Both are popular for SSB portable work because few QRP rigs cover phone as conveniently.

Mountain Topper (the MTR series): compact multiband CW rigs designed for summits-on-the-air style activations, with very low current draw and a small footprint.

Penntek TR-35: a single-band CW transceiver kit, about 5 W, with a swappable band module. It suits people who want a focused build and a simple radio.

Hendricks QRP Kits: a long-running source of small kits, usually single-band CW rigs and accessories, good for learning how a superhet or direct-conversion design goes together.

Pixie-style transceivers: very simple, often just a couple of transistors, using the transmitter's final stage as a receiver mixer or audio amp. They are cheap and educational. Don't expect good selectivity, and keep in mind that on a busy band the receiver will hear a lot of wide signals at once.

Calling frequencies. The commonly used QRP centers of activity on CW are around 1.810, 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz. SSB QRP activity is often listed near 3.985, 7.285, 14.285, 21.385 and 28.385 MHz. Check these against your region's band plan, because 40 m in particular differs between regions. Remember that they are meeting points rather than reserved frequencies, so call, then move off if the spot is crowded.

Antennas. Popular choices are the end-fed half-wave with a 49:1 transformer, a linked dipole, an inverted-V on a lightweight mast, and a random wire with a counterpoise. Keep the feedline short and use low-loss coax or none at all. A resonant antenna is often better than a tuner hiding an inefficient one. Get the radiator up as high as you can, even on a fishing pole.

Batteries. A 4-cell LiFePO4 pack is about 13.2 V nominal, around 14.4 V fully charged, and it holds its voltage well through the discharge curve. That suits rigs that dislike sagging supply voltage. A 3S LiPo is 11.1 V nominal and up to 12.6 V charged. Whatever you choose, check the rig's input range, fuse the positive lead and use a proper balance or charge setup for the chemistry.

What are you running, and what's the one change that improved your results the most?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On antennas, the main trap with an end-fed half-wave is assuming the transformer does all the work. The radiator length, the coax acting as part of the antenna, and the lack of a real counterpoise all change how well it behaves. A choke a little way down the feedline helps keep RF off the coax and out of your receiver. It is also worth carrying a short counterpoise wire if the SWR is odd.

For SSB, a few dB of speech processing or compression, if your rig has it, does more than extra power would at the same price. A 5 W signal with good audio and a clean edge can be copied by operators who would miss a muddy one. CW is the more forgiving mode, which is why most kits and ultralight radios are built around it.

Also test the whole setup at home first: rig, key, battery, antenna and logging method. Many of the failures people hit in the field are cabling, a bad connector or a dead battery rather than propagation.

  • Moderators

Regarding the kit side, I'd split the choice by what you want from it. A Pixie is a good way to understand a transmit/receive switching idea, but it won't be the radio that fills a log, so treat it as a lesson. Something like the TR-35 or a Hendricks kit gives you a usable radio at the end, with a proper receiver, and that tends to keep a project from ending up in a drawer.

If you're mainly interested in SOTA or park-style activations, the weight and current draw matter more than the feature list. A multiband CW-only rig such as a Mountain Topper is attractive because the whole station, including antenna and battery, can be packed small. If you want to talk on SSB as well, the KX2 or KX3 makes more sense, at the price of more money and more battery use.

On contests, QRP-ARCI events are a friendly way to see how your station compares with others. Read the exchange and power classes before the weekend so you know what you need to send. Also log your actual output, not just the dial setting, because a rig's power meter can read differently from what is really leaving the antenna.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.