Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig on the bench: what's your order of operations for no TX / no RX faults?

ci_cover.jpg

I'd like to compare approaches to troubleshooting a rig that is dead, deaf or won't transmit. Most failures come down to a handful of causes, but it's easy to burn an evening chasing the wrong one if you skip the cheap checks. Here is the order I think makes sense, and I'd like to hear where you'd change it.

1. Power first, and measure it under load. A supply that reads 13.8 V with nothing connected can sag badly once the rig draws current. Measure at the rig's DC connector, not at the supply terminals, because a corroded fuse holder, a marginal Anderson contact or thin cable can drop a volt or more. Check the inline fuses and the internal fuse. If the fuse is blown, don't just replace it and hit PTT. A blown fuse with reverse polarity or a shorted protection device means something has already failed, so use a current-limited bench supply for the first power-up.

2. Decide whether it is one fault or two. No receive and no transmit together usually points to something common: supply rail, regulator, microcontroller or PLL not locking, a blown rail fuse, or a dead reference oscillator. Only one of them points to a path-specific fault. If the display is alive and the rig tunes but is deaf, work from the audio end toward the antenna. Touch the volume control hot lug with a screwdriver, listen for a buzz, and move back stage by stage with a signal generator or an RF probe on a scope. If receive is fine but there is no output, check bias, drive and the final stage.

3. Protection faults are not always real. If the rig drops power or shows a high-SWR warning, put it on a known-good dummy load before touching the antenna system. If the fault goes away, it is the antenna, coax or tuner. If it persists into a dummy load, suspect the rig's own SWR bridge or detector diodes, the reflected-power sense circuit, a bad solder joint on the directional coupler, or a protection circuit reacting to a real fault like a drifting bias or oscillation. Don't defeat the protection to see if it transmits.

4. Blown finals are usually a symptom. Before replacing a dead RF MOSFET or transistor, find out why it died. Common causes are high SWR, overvoltage, parasitic oscillation, a failed bias supply, or a failed driver. Check the gate or base bias network, the bias regulator, the thermal-compensation diode or transistor, and any resistors that have drifted open. When you fit new devices, use the correct part and not just something with similar ratings, since RF gain and capacitance matter. Turn the bias to minimum and bring it up to the manual's idle current on a current-limited supply with no drive.

5. Capacitors and contacts. Aging electrolytics cause hum, low audio, supply noise and odd startup behaviour. In older rigs and some SMD designs, leaking electrolyte can corrode traces and nearby parts. Clean the board with isopropyl alcohol and inspect for damaged traces before you replace anything. For replacements, match capacitance and voltage and use low-ESR, 105 °C parts where appropriate. Don't swap ceramic types casually in RF paths, because the dielectric affects stability. For intermittent controls, band switches and relays, use a proper contact cleaner sparingly and clean the cause rather than flooding the assembly.

6. Leave the alignment slugs alone until the fault is found. Alignment is for restoring performance after repairs or drift, not for finding a dead stage. Use the service manual's procedure, mark original positions, use a non-metallic tool, and have a signal generator, frequency counter, RF power meter and dummy load available. A rig that is out of alignment usually still receives something.

Test equipment. At minimum I'd want a decent DMM, a current-limited bench supply, a dummy load and the service manual. A scope is next because it shows supply ripple, audio presence and oscillation that a meter averages out. After that come an RF probe, signal generator and a way to measure return loss or filter response, such as a NanoVNA.

What would you do differently? Do you check the supply and protection first, or go straight to signal tracing? And what is the first thing you pull out of the toolbox when a rig comes in with no information on what happened?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I agree with starting at the supply, but I'd go further on ripple and noise. A DMM only tells you the average voltage. Put a scope on the rail, AC-coupled, and look for ripple, spikes and a rail that dips when the radio switches to transmit. Many strange problems, like intermittent resets, hum on audio, birdies and a noise floor that changes when you touch things, come from a poor supply or filter capacitor and not from the radio's RF circuitry.

If the rig is noisy only on one supply, try it on a linear supply or battery. If the noise disappears, the culprit is probably a switching supply or its wiring. If it stays, try moving the rig away from LED lamps, chargers and computers, and see whether ferrites on the DC lead make a difference. On the bench, remember that the scope ground clip is the same as mains earth on many scopes, so be careful where you clip it. In mains-powered gear without an isolation transformer, a grounded probe on the wrong node can cause damage.

On capacitors, in-circuit ESR meters are useful, but a low reading in-circuit can mislead if parallel paths exist. If a cap looks suspicious, lift one leg before you condemn it.

  • Moderators

One thing I'd add on finals: do not apply drive or full voltage after replacing the devices until you've verified the bias circuit. A common mistake is to replace a blown transistor or MOSFET and then power the rig with the bias circuit still faulty, which kills the new part within seconds. Check the bias voltage range, make sure the adjustment pot isn't open or noisy, and check that the voltage actually reaches the gate or base. Use a series lamp or a current-limited supply if you can.

Also check the output filter relays, low-pass filter capacitors and inductors, and the antenna changeover relay. A relay with burned contacts can present a bad load, and the finals pay for it. A multimeter diode check will catch a shorted junction, but it can't tell you whether the device has lost gain or that a MOSFET is leaky. The SWR protection circuit might still be perfectly healthy and doing its job. It may be telling you the output filter or the relay is wrong.

On manuals, I'd treat the voltage chart and block diagram as the most useful pages. They let you decide where to measure before you open the radio. If there is a service bulletin or known-failure list for that model, read it first, because some models have repeat failures that aren't obvious from the schematic alone.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.