Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24-hour EMCOMM field station: power budget, generator vs. LiFePO4, antennas, grounding and noise

ci_cover.jpg

I'd like to work through a basic field station design for a 24-hour EMCOMM-style deployment, such as a served-agency support location or a shelter with a failing comms path. The station has one HF rig, one VHF/UHF rig, a laptop for digital modes and logging, a few handhelds on chargers, and some lighting. I'm asking about the order in which the decisions should be made, not just the gear list.

My view is that power should be sized first, because it drives everything else. Take the rig's real transmit current, not the front-panel wattage. A typical 100 W HF transceiver draws roughly 20 A or more at 13.8 V on full-power transmit and only a couple of amps on receive. The average depends on the mode. SSB voice has a low duty cycle. FT8, RTTY and other keyed or continuous digital modes can run near 50 percent or higher, so the sensible move is to drop to 30-50 W and accept a slightly weaker signal in exchange for much less heat and battery drain.

As a rough budget, a 100 Ah LiFePO4 battery stores around 1,280 Wh nominal. Leave some margin for the BMS cutoff, converter losses and cold weather. If the station averages 6-8 A over a mixed duty cycle, including the laptop and lights, that is about 100 Wh per hour, so a single 100 Ah battery should last about half a day with margin. That number is only as good as the measurements behind it, so put a DC watt-meter or shunt on the real setup and log it for an hour of simulated traffic.

LiFePO4 has two quirks. The voltage curve is very flat, so a voltage meter tells you little about state of charge, and a shunt-based monitor is much better. The pack also holds about 13.2-13.3 V under load until it nears empty, then drops quickly. Some radios and accessories are happy with that, but check your own gear's input range. Also confirm that your charger or solar controller has a LiFePO4 profile, usually around 14.2-14.6 V absorption, and not a lead-acid one that cooks or undercharges the pack.

For long deployments, the inverter generator is the backup that keeps the battery topped up. The practical rules are:

  • Put it well downwind and away from tents and vehicle air intakes, and run a CO alarm in any occupied shelter.
  • Never refuel it while hot or running, and keep the fuel stored separately.
  • Use GFCI protection on the distribution side.
  • Run it on a lightly loaded battery charger or power supply, not directly on the radio's AC input, unless you know it is clean.

Solar helps most as a trickle or daytime supplement. Panel placement, shading and the controller matter more than panel size. MPPT controllers can be noisy on HF, so test with the receiver before deployment. Sometimes a PWM controller or a ferrite-treated lead fixes it.

On antennas, the best plan is usually simple. For regional EMCOMM on 40 m and 80 m, a low dipole or inverted V roughly 10-30 ft up is often a better NVIS choice than a tall vertical. For VHF/UHF, a small mast with a decent gain antenna and low-loss coax beats a handheld rubber duck by a large margin. Keep the mast well clear of power lines, with a fall zone larger than its total height. Use non-conductive guy line, and stake or weight the base with the worst wind in mind, not the forecast.

Coax loss is worth looking up on the cable datasheet. At HF, even modest coax is usually fine for a short run. At 146 MHz and especially 440 MHz, thin coax such as RG-8X loses far more than something like LMR-400. A 50 ft run that costs a dB or two can be the difference between reaching the repeater and not. Put a 1:1 current choke at the feedpoint and another near the radio to cut common-mode current, which causes a lot of field RFI.

Grounding needs to be kept in perspective. A short ground rod does not give you a good RF ground, and it is not lightning protection. The honest lightning plan is to monitor the weather, disconnect and lay down the antennas early, and move people away. Safety bonding of equipment should follow the generator's manual, since some inverter units bond neutral to frame and some float it.

The checklists are where deployments usually succeed or fail. My starting list:

  • Site survey: power lines, wind exposure, ground slope, parking, and a noise check on a few HF bands with the receiver before anything else.
  • Order of setup: shelter, power, antennas, then radios, and a written test sequence for each.
  • Teardown: reverse order, inspect and coil coax, count every item against the packing list, and note any damage.

What do you think is the most commonly missed item in this plan? And what would you change in the order of setup?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The sequencing is right, but I'd add one thing to the power section: decide your failure behavior up front. If the battery is the primary source, what happens at the BMS cutoff? A LiFePO4 pack that disconnects abruptly can drop the radio, laptop and logging in the middle of a net. Put a low-voltage warning on a shunt monitor, and set a rule such as "at 20 percent remaining, we start the generator or shed non-essential loads." Distribution matters here too. A fused DC panel with separate circuits for the radios and for lighting/charging lets you drop the less important loads without touching the radio side.

On the generator, one thing is easy to overlook. A lightly loaded inverter generator on eco mode can have worse regulation and sometimes more noise than one at a steadier load. If you only run it as a charger, test whether the charger or the generator's output is the source of the hash. Plug a small AM or SW receiver near the cord. Sometimes a few turns of the cable through a large ferrite fixes the noise, and sometimes moving the whole generator 30 ft farther away is the only cure.

  • Moderators

For antennas, I'd split the plan into a primary and a fast fallback. The primary might be a 40/80 m inverted V on a fiberglass mast. The fallback should be something one person can deploy in a few minutes, such as an end-fed wire or a vertical with radials, so you can get on the air before the full system is up. For NVIS, height matters less than you'd think. A dipole at 0.1-0.25 wavelength up on a quiet band often performs fine, and it is easier to keep out of the way of people and vehicles.

Also separate the radio area from the noise sources physically. Keep the generator, charger and solar controller on one side, the antenna feedlines on the other, and run the coax straight out of the shelter, not parallel to AC and DC cables. If something is noisy, change one thing at a time and write down what you changed. That log is also useful afterward, because a deployment note like "MPPT controller raised the noise floor on 20 m, fixed with ferrites on the PV lead" is exactly what the next team needs.

For the shelter, plan for rain, wind and condensation. A tarp or tent with a defined cable entry point, a place for the laptop away from drips, and red or low-level lighting for the operating position all cost very little and prevent a lot of problems on a long night.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.