Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a first homebrew station: build order, and what to measure at each step

ci_cover.jpg

I'd like to set out a build order for someone moving from kits to scratch-built gear, and see where people disagree. The usual advice is to build whatever looks fun, but the order matters because each project gives you a tool or a skill the next one needs.

A sequence that makes sense to me:

1. Power supply and protection. Before any radio, build or buy a clean 12-13.8 V supply with a fuse and a reverse-polarity diode (or a series diode plus fuse). It sounds dull, but most dead kits come from a reversed lead or a supply that sags under keying. A simple regulated supply with a few hundred millivolts of ripple will make a direct-conversion receiver hum.

2. Dummy load and RF probe. A 50 ohm dummy load and a diode probe for the multimeter let you see RF without an oscilloscope. Check the load's rating and frequency range before trusting it.

3. A crystal-controlled QRP transmitter such as a Tuna Tin 2 style design (Doug DeMaw W1FB's classic: a crystal oscillator driving a single transistor amplifier, about a watt). It teaches you to tune a transmitter into a dummy load, measure output power and see what a low-pass filter does.

4. A direct-conversion receiver. It needs a local oscillator, a product detector and a lot of audio gain, so it is the cheapest way to learn how a mixer works. Expect problems with AM broadcast breakthrough, hum and microphonics, and expect the receiver to hear both sides of zero beat.

5. A transceiver. A Pixie-type circuit is a good low-cost curiosity, but its selectivity is poor and it is easily overloaded. A BITX-style design or a uBITX kit is a bigger step: SSB, mixers, a crystal filter, bilateral amplifiers and, on the uBITX, a Si5351-based synthesizer with a microcontroller.

6. Accessories: SWR bridge, keyer, low-pass and band-pass filters. These are small projects, but they only become useful once you have something to measure.

Questions for the group. Would you put the direct-conversion receiver before the transmitter? And what is the minimum test equipment you would insist on before someone puts a homebrew transmitter on the air: a frequency counter, a scope, a NanoVNA, an SDR for checking harmonics?

  • Replies 2
  • Views 27
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd swap 3 and 4 only if the builder has no transmitter license yet. A receiver can be built and used on day one, and nothing about it can cause interference. A direct-conversion receiver also doubles as a test instrument: tune it near your crystal oscillator and you can hear the signal, the drift and the key clicks.

On direct-conversion problems, two fixes cover most of them. First, put a simple band-pass filter ahead of the mixer so AM broadcast stations are attenuated before they hit the detector. Second, keep the audio stage's gain and bandwidth sensible. A low-pass response in the audio chain, even a few RC sections, makes a big difference to how tiring the receiver is. Hum usually comes from the supply or ground layout, not the mixer, so check those before redesigning anything.

For layout, Manhattan-style construction on copper-clad board, or dead-bug style for small circuits, is fine at HF. Short leads in the oscillator and mixer matter more than a neat appearance.

  • Moderators

On the transmitter side, the minimum I'd want before going on air is a dummy load, a way to measure power (an RF probe and a calculation is acceptable at QRP: P = V_rms² / 50, with V_rms roughly the peak reading divided by 1.414 after correcting for diode drop), and some way to look at harmonics. A low-pass filter is not optional on a single-transistor final, because the output of a Class C or hard-driven stage can have strong harmonics. A 5-pole Chebyshev low-pass for the band is a small build and the values are easy to look up.

For harmonic checking, an SDR or general-coverage receiver works, but never connect the transmitter output straight to it. Use a dummy load with a sampling tap or a good attenuator, or the front end can be damaged and you will see overload spurs that aren't really there. A NanoVNA is useful for sweeping the filter itself and for checking antenna match, but it is not a spectrum analyzer, so it doesn't replace checking what the transmitter actually emits.

For the uBITX and similar multiband kits, the output filtering and spurious output are worth checking on each band you plan to use, since a filter that is fine on one band may be marginal on another. Treat any published performance numbers as a starting point and verify them on your own unit.

On soldering: a temperature-controlled iron, thin rosin-core solder, fresh flux and a clean tip fix most intermittent problems. Cold joints on toroid leads are common, so scrape the enamel properly or use a tinned lead test before winding another coil.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.