Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

VHF/UHF antenna choices: when does each design actually make sense? (J-pole, slim jim, 5/8 whip, collinear, yagi)

ci_cover.jpg

Antenna threads often turn into "which one has the most gain," but the better question is what the antenna has to do. Let's compare the common VHF/UHF designs by job: base station, mobile, repeater access, weak-signal work, or satellites.

Quarter-wave whip. It is about 19 inches at 146 MHz and about 6.5 inches at 446 MHz. It is simple, mechanically tough, and tolerant of a mediocre ground plane. Its pattern is omnidirectional in azimuth with a fairly high takeoff angle. That is fine for local FM work, but it has no gain over a dipole. It needs a ground plane, such as a vehicle roof, to work as intended.

5/8 wave. On a decent ground plane, a 5/8-wave vertical gives roughly 3 dB over a quarter-wave. Its lower takeoff angle puts more energy toward the horizon. It needs a matching network, usually a coil at the base, and it depends more on ground-plane quality than a quarter-wave does. On a small or off-center ground plane the pattern can tilt upward and the gain advantage shrinks. Dual-band mobile whips combine different electrical lengths in one radiator, so their VHF and UHF behavior can differ.

J-pole and slim jim. Both are end-fed half-wave radiators with a quarter-wave matching section. The J-pole is a half-wave element with a shorted stub. The slim jim is a folded variation, usually built from ladder line or tubing. Both give roughly dipole-like gain, and the slim jim tends to have a slightly lower takeoff angle. They are cheap and easy to build. The weak point is common-mode current: with no ground plane, the coax shield can become part of the antenna, which distorts the pattern and shifts the SWR when you touch or move the feedline. A choke (ferrite or coiled coax) and a good feedpoint tap help.

Collinear. Stacked, phased half-wave sections narrow the elevation beam and raise gain, commonly 3 to 9 dBi depending on length. The tradeoff is a flatter pattern, so mounting height and mast verticality matter more. A tilted mast or a very high site relative to the users can leave nearby stations in the nulls. Collinears suit repeater sites and coverage over flat terrain, and they are less useful in hilly areas where signals arrive at varied angles.

Yagi. A yagi trades coverage for gain and front-to-back ratio. A three-element is often in the 6 to 8 dBi range, and gain grows with boom length. It is the usual choice for a known direction, such as one repeater or a weak-signal contact. Polarization matters: FM repeaters are almost always vertical, while SSB/CW weak-signal work on 2 m and 70 cm is conventionally horizontal. Mixing polarizations can cost many dB in practice.

Feedline and connectors. Coax loss rises quickly with frequency, so a feedline that is fine at 2 m can eat your gain at 70 cm. Thin RG-58 loses several dB per 100 ft at VHF and roughly double that at UHF. LMR-400-class cable is about 1.5 dB per 100 ft at 150 MHz and 2.7 dB at 450 MHz. PL-259/SO-239 connectors are acceptable at VHF but are not constant-impedance and are poor above about 300 MHz. N-type connectors are constant-impedance, sealed with an O-ring, and a better fit for UHF and outdoor runs. Waterproofing matters whichever type you use.

Mounting and SWR. NMO mounts need a 3/4-inch hole and give a solid, low-loss connection. Magnetic mounts couple to the roof partly capacitively, so a clean surface and a centered position help, and the coax lead can be damaged by pinching in a door. Remember that SWR is not efficiency: a dummy load shows 1:1 and radiates nothing, and lossy coax can make a bad antenna look better. Check SWR at the antenna when you can, across the whole band you use.

For repeaters, satellites, or a mobile install, what compromises are you working with, and which of these tradeoffs matters most for your setup?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On satellites, the main issue is that a LEO pass sweeps across the sky, so a fixed omni gives little margin at low elevation. Many operators use a small handheld yagi on a dual-band FM radio, and a good design can work the bird at both ends of the pass. Since the satellite's orientation changes, polarization is not fixed, and crossed yagis with circular polarization reduce fading. A single linear yagi can still work if you rotate it to minimize the fade. Doppler is also a factor on UHF, so you retune the receive side during the pass.

Gain alone doesn't solve it. A higher-gain beam needs better pointing and a narrower tracking window. For beginners, a modest beam and short low-loss cable are usually more productive than a large array on a tall mast.

  • Administrators

A point on mobile 5/8 versus quarter-wave: the 5/8 usually wins only when the ground plane is large and the antenna is centered. On a trunk lip or fender mount, the pattern is lopsided toward the metal and the nominal gain is partly theoretical. A quarter-wave on the roof is often competitive on real roads, especially in hills where the low-angle advantage matters less than a clean, well-grounded feed.

On the J-pole point, if the SWR changes when you touch the coax or move the cable, that points to common-mode current. Adding a choke a quarter wave or so below the feedpoint, or routing the coax away at a right angle, can stabilize it. And on the connector question, if a run is outdoors at UHF, using N connectors from the start is cheaper than chasing intermittent water-related loss later.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.