Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting clean, effective SSB audio: mic gain, ALC, processing, bandwidth and weak-signal habits

ci_cover.jpg

SSB audio is one of those areas where small adjustments make a big difference, and where it is easy to chase the wrong fix. This post sets out a baseline sequence for setting up a transmit chain. The idea is to get a clean, intelligible signal first, then add only as much processing as the band conditions justify.

Start with the microphone and distance. Most intelligibility problems begin before the radio. A mic that is too far away picks up room reflections and noise, and a mic that is too close gives boomy bass and plosives. Mic placement guidelines vary by element type, but a few centimeters off-axis, so that your breath does not hit the capsule directly, works for many dynamic and headset mics. Keep the distance consistent, because moving around makes the audio level swing and the processor work harder. A foam windscreen is cheap and helps. Hard walls and bare desks near the mic add reflections, and soft furnishings help more than most people expect.

Set mic gain by the ALC, not by guesswork. The ALC (automatic level control) protects the transmitter from being overdriven. It is not a loudness knob. A common approach is to speak in a normal, steady voice and raise the mic gain until the ALC meter just starts to move on voice peaks, then back off slightly. Check your rig's manual for the target range, because meter scales differ. If the ALC is pinned during speech, the stage is being overdriven, which shows up as distortion and a wider signal. Reducing power with the RF power control while leaving the ALC deep in action does not fix the problem, since the drive into the ALC stage is still too high. The correct fix is to lower the mic gain.

If you run an external amplifier, check for ALC feedback from the amp and keep drive low enough that the amp stays linear. A flat-topped, clipped signal from a linear running too hard is a common cause of splatter that the operator cannot hear on the monitor.

Use the speech processor sparingly. Compression raises the average-to-peak ratio, which increases average power. That can help a signal stand out in noise. Too much compression raises background noise, makes sibilance and breath sounds more prominent, increases distortion, and can broaden the signal. For many setups, a few dB of compression is the useful range. If you cannot hear a clear improvement from a recording or from reports, turn it down. Rigs differ here: some have RF clipping, some have AF compression, and the effect depends on how they are implemented. In general, the processor adds the most value under noisy conditions with a weak signal at the other end, and it is less useful on a strong, quiet band where natural audio sounds better.

Use the TX equalizer to remove what is not needed. Speech intelligibility sits mainly in roughly 300 to 3000 Hz. Rolling off low frequencies, below about 100 to 200 Hz depending on your voice, frees transmitter power from content that does not help the listener. A mild lift in the 2 to 3 kHz region adds presence, but too much creates harshness and hiss. Many rigs also let you set the transmit bandwidth, for example a narrower setting for DX or crowded bands and a wider one for a casual local chat. A narrower transmitted signal concentrates power in the speech range and takes up less spectrum, though it does sound more communications-like.

Monitor, with some limits. The monitor function lets you hear your own transmit audio, which is useful for spotting distortion, hum, or harshness. Use headphones so the audio does not feed back into the mic. Be aware that many rigs derive the monitor signal from the audio chain and not from the actual RF output, so it may not reveal splatter or amplifier problems. For a more complete check, use a second receiver or an SDR to look at your signal, or ask a local station for a careful report. A two-tone test with a suitable scope or spectrum display is the standard way to examine linearity, if you have the equipment.

Choose the correct sideband. The convention is LSB below 10 MHz (160, 80 and 40 m) and USB above it (20, 17, 15, 12 and 10 m). On 60 m, USB is the usual practice. Following this makes it easy for others to tune you in without switching sidebands. Exceptions exist, such as certain nets, but the convention is the default.

Receive filtering for weak stations. A typical SSB receive bandwidth is about 2.4 kHz. When there is interference, narrowing to 1.8 to 2.1 kHz can cut adjacent signals, at some cost in naturalness. Passband shift or IF shift lets you move the window away from an interfering signal without retuning. Turn on the noise reduction gradually, since heavy settings produce artifacts that can make a weak signal harder to copy. Use the preamp only when the band noise floor is below the receiver noise; on the lower bands, extra gain often just amplifies atmospheric noise. If a strong signal is overloading the front end, the attenuator can actually improve copy. AGC speed also matters: a slow AGC can mask weak signals right after a strong one.

Working DX. In a pileup, clarity and timing matter more than loudness. Listen to how the DX station operates, including whether they work split, and call only when you understand the pattern. Send your callsign in standard phonetics, clearly and at a normal pace, and avoid repeating it endlessly. Overdriving the processor or running too wide does not help you get heard, and it can annoy neighboring stations. A clean signal with a moderate processor setting and well-managed power is often copied better by the DX operator than a loud, distorted one.

What settings have you found give the best balance on your rig? Specific details such as the microphone type, transmit bandwidth, compression level and ALC reading would make it easier to compare setups.

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One thing worth adding about the processor is that the meter and the audio quality do not always agree. Many rigs show a compression meter, but the same reading can sound quite different depending on mic gain, EQ, and whether the compression is applied before or after the equalizer. If you boost highs first and then compress, the compressor reacts strongly to sibilance, and the result can sound harsh. It can be better to set the EQ first with the processor off, then add compression gradually.

A simple way to judge it is to record your transmit audio, either through the rig's built-in recorder if it has one or by listening on a second receiver, and compare processor off, light, and heavy. Compare them at low volume and through a small speaker as well, since that is closer to what the other operator hears. If the heavier setting does not make the words easier to understand, it is only adding noise and distortion.

Also check that the monitor level is not misleading you. A loud monitor in the headphones can make you speak more quietly or louder than you realize.

  • Administrators

On the receiving side, I would stress that narrower is not always better. A 1.8 kHz filter can make a signal easier to copy in QRM, but if the other station has a naturally wide or bass-heavy voice, you may lose the part of the speech that carries the consonants. On a weak but clean band, try 2.4 kHz first and use passband shift to move away from an interferer before you narrow the filter.

The same goes for noise reduction. Light settings can ease listening fatigue, but strong NR can remove the speech information that you need for a weak station. The notch filter and noise blanker are more targeted tools if the problem is a carrier or impulse noise.

For DX, it also helps to check where the other operator is listening before you call. If you are using split, make sure the RIT or the second VFO really is where you think it is and that the TX bandwidth is not so wide that it overlaps the neighbors. A quick check of your transmit frequency on an SDR or second receiver before you call can avoid a lot of wasted calls.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.