Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Choosing an SDR chain for HF and VHF: dynamic range, upconverters, antennas and which software to pair with it

ci_cover.jpg

This is a planning question about the whole receive chain, not only which dongle to buy. The goal is general-coverage listening from HF through VHF/UHF, plus decoding digital signals (FT8 and other WSJT-X modes, DMR/P25 where legal to monitor, ADS-B, AIS, weather satellites). Here is how the pieces seem to fit, and where I'd like corrections.

Hardware tiers, roughly. RTL-SDR dongles use an 8-bit RTL2832U ADC with about 2.4 MHz of reliably usable bandwidth. They are cheap and good for VHF/UHF, but they overload easily in the presence of strong broadcast signals. HackRF One is also 8-bit, but it covers 1 MHz to 6 GHz, with up to 20 MS/s and transmit capability (half duplex). SDRplay RSP-series receivers and the Airspy line (R2, Mini, HF+) use higher-resolution converters with better front-end filtering, and cost more. LimeSDR is a 12-bit transceiver with a very wide tuning range, aimed more at experimenters than at casual listening.

For HF, the options seem to be: (1) direct sampling on an RTL-SDR, (2) an upconverter in front of a dongle, or (3) a receiver that covers HF natively. I'd like to understand the trade-offs in practice, especially regarding noise and overload, and how people decide between a more expensive receiver and a cheaper one with external filtering.

On software: SDR# and HDSDR on Windows, SDRuno for SDRplay hardware, GQRX on Linux/macOS, CubicSDR as a cross-platform option. Which of these handle audio routing to decoders most cleanly, and what is the least painful way to run a panadapter or bandscope next to a conventional transceiver without risking the SDR during transmit?

  • Replies 2
  • Views 27
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with dynamic range, because it explains most of the confusion. An ideal ADC gives roughly 6 dB per bit, so 8 bits is about 48 dB before real-world losses, and the effective number of bits is lower. Everything the antenna delivers across the whole sampled bandwidth competes for that range, not just the signal you are tuned to. A strong FM broadcast station or local AM transmitter can push the converter near full scale while the weak signal you want sits near the quantization noise. That is why turning the gain up often makes things worse. Set gain so the noise floor on the spectrum is just visibly above the receiver's own floor, then stop. If the waterfall fills with ghost signals or spurs that move when you change gain, that is overload or intermodulation, not an antenna problem.

Filtering helps more than extra gain. A broadcast-FM notch is a common first step for RTL-SDR on VHF, and bandpass filters for the band of interest help at HF. SDRplay receivers include switchable notches for broadcast bands in hardware. Pre-LNA filtering is where it matters: filter before amplifying, not after.

At HF, external noise (atmospheric, man-made, local interference) usually exceeds receiver noise, so a low noise figure is less important than at VHF/UHF and above. A modest antenna and a clean receiver often beat a high-gain preamp feeding a weak converter. At VHF and up, noise figure and feedline loss matter more, so a mast-mounted LNA (powered via bias tee if your hardware supports it) can help, as long as you check that nothing in the path presents a DC short to the bias voltage.

Antennas: a dipole or discone is a sensible starting point for VHF/UHF. For HF, a longwire with a 9:1 unun, a small active loop, or a magnetic loop each have different noise and overload behavior. Active antennas can overload your receiver on their own. Local noise from switching power supplies, LED lighting and the PC itself can swamp everything, so put the dongle on a USB extension, add ferrites, and use a common-mode choke on the coax. If the noise floor drops when you unplug things, you've found the problem.

Direct sampling on an RTL-SDR works for casual HF listening, but sensitivity is limited and aliasing and overload are more likely without a lowpass filter. It is workable, not great. A native HF receiver is cleaner. Check the published specs for your specific model; frequency coverage and bandwidth vary by version.

  • Moderators

Upconverters first. A typical one mixes HF with a local oscillator (for example 100 or 125 MHz) so the RTL dongle sees HF in its normal tuning range. In SDR# or similar you apply a frequency offset equal to the LO, so the display reads true frequency. Watch for LO leakage, mixer images, and spurs; shielding and a lowpass filter ahead of the mixer matter. A good upconverter can work well, but a native HF receiver avoids the extra stage.

Software, roughly: SDR# has a large plugin ecosystem and is easy to start with. SDRuno is built for SDRplay hardware and has good tools for managing multiple VFOs and memory. HDSDR is long-established, uses ExtIO drivers, and includes CAT/rig-control and an IF-output panadapter workflow. GQRX is the natural choice on Linux and macOS and works with many devices through gr-osmosdr or SoapySDR. CubicSDR also goes through SoapySDR, which suits unusual hardware like LimeSDR. Which is best depends mostly on your operating system and hardware; try two and see which display, filter and AGC behavior you prefer.

For digital decoding, route demodulated audio to the decoder through a virtual audio cable: VB-Cable or similar on Windows, a loopback device on macOS, a PulseAudio/PipeWire null sink on Linux. Set the SDR to USB, keep the audio level moderate to avoid clipping, and make sure the system clock is accurate for WSJT-X time-slotted modes. For ADS-B, AIS, pagers or ISM sensors, dedicated tools (dump1090-type decoders, rtl_433, multimon-ng, SatDump and so on) often read IQ directly and skip the audio path. Check your local regulations before decoding anything that is not a public broadcast or amateur signal.

Panadapter: the safest approach is to take a low-level IF or RF tap from the transceiver, not to share the main antenna without protection. If the SDR shares the antenna, use a proper splitter and receive-protection with transmit inhibit, because even modest transmit power can damage an unprotected front end. A dedicated receive-antenna output, if the radio has one, is the cleanest option. Syncing the SDR display to the rig frequency by CAT keeps the bandscope aligned with the transceiver.

Last practical point: frequency accuracy. Cheap dongles drift with temperature, so apply a ppm correction, or choose a model with a TCXO if you plan to decode narrowband modes.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.