Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Baseline field station for a 12-hour EMCOMM shift: power, antennas, grounding and noise. What would you change?

ci_cover.jpg

This is a baseline layout for a single-position HF/VHF station at a tent or canopy deployment, with no mains power assumed. It is meant to be picked apart. Where do you disagree, and what gets missed in the real world?

Power. The core is a LiFePO4 battery (12.8 V nominal, usually 4S) sized from a rough energy budget rather than a guess. A 100 W HF rig draws roughly 1 to 2 A on receive, plus the display and any accessories, and perhaps 20 A on transmit peaks. A 2 m/70 cm mobile at 50 W is usually 10 to 12 A while transmitting. Weight it by duty cycle: if net traffic is mostly listening, average current may be only a few amps. Multiply amp-hours by 12.8 to get watt-hours, then subtract 20 percent or so for margin and for the fact that you don't want to run the pack flat. A 100 Ah pack is about 1280 Wh on paper. Add the laptop, lights, phone charging and a radio for the served agency, and the budget changes quickly.

The battery feeds a fused distribution block with the fuse close to the battery positive terminal. Each radio gets its own fused leg, with wire gauge chosen for voltage drop at the transmit current rather than just for the fuse rating. Powerpoles (or another keyed, polarity-safe connector) are used throughout, and everything is labeled. A generator is the backup for recharging, not the primary source. A small inverter generator sits well downwind of the operating position and the tent, on level ground, with a CO alarm in the shelter and the fuel stored away from it. Solar is a supplement: an MPPT controller with a LiFePO4 charge profile, with the panels placed away from the antenna.

Antennas. For regional HF, a low dipole or inverted V for 40 m and 80 m is a common NVIS-style starting point, supported by a fiberglass mast. For VHF/UHF simplex or repeater work, a mag-mount or a mast-mounted vertical clear of the tent. The mast is guyed with visible markers, anchored for the expected wind, and kept far from overhead lines. The distance to any line should be more than the full height of mast plus antenna, and more if it can fall in a direction you can't control.

Coax and noise. Use low-loss coax for VHF/UHF runs, since a long run of thin coax can eat a lot of a 70 cm signal. At HF, thinner coax is usually fine. A common-mode choke goes at the radio end and often at the feedpoint. Feedline is routed away from power cables, strain-relieved, drip-looped, and protected where people walk. Before the net starts, check the noise floor with every accessory powered: the laptop, the chargers, LED lights, the solar controller and any DC-DC converters. Cheap switching supplies are common culprits, and each one should be tested individually.

Grounding. All station equipment is bonded together at one point. A driven rod is for the station's safety bond and for any generator requirements. It is not a lightning plan. If thunderstorms approach, the plan is to disconnect antennas and stop operating. Verticals need a proper radial system or counterpoise, not a rod.

Setup order is: site survey and wind check, shelter, generator placement, antenna and mast, feedline, power distribution, radios, noise check, then log and check-in. Teardown reverses that, with a final sweep of stakes, trash and fuel. What does your list include that this one doesn't?

  • Replies 2
  • Views 24
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd tighten the power section first. Putting the fuse at the battery is correct, but a lot of LiFePO4 packs have a BMS with a current limit. If a 100 W HF rig and a VHF mobile are both transmitting, plus an inverter running a laptop charger, check the continuous and surge ratings of the pack rather than assuming it will carry the load. A BMS trip in the middle of a net is a bad way to find out. Also check the low-temperature charging rules. Most LiFePO4 cells shouldn't be charged below freezing unless the pack has built-in protection, which matters if you plan to rely on solar or a generator-fed charger on a cold morning.

On the generator, I'd treat it as an hourly-load question. Inverter generators are quiet but they are most efficient and least noisy at moderate load, so using the generator to recharge the battery through a proper charger in blocks can beat running it all shift. Keep it far enough away that its exhaust and noise are not at the tent, and put the CO alarm at head height inside where people sleep or rest. Don't run the generator under the canopy or backfeed the station from it.

  • Moderators

Good starting list. Here are some points I would add or push back on. First, the noise check. Don't only test with everything on at once. Turn items on one at a time and watch the S-meter on a quiet band, because a single bad wall-wart can mask what else is going on. If the noise is on the feedline, a choke may help. If it comes in through the power leads, a ferrite on the DC cable or a different supply is usually the fix. Moving the antenna farther from the shelter often does more than any filter.

Second, I'd soften the grounding statement slightly. A single-point bond is sensible, but what that point is connected to depends on the setup. A battery-only station has different needs from a generator-fed one, and a vehicle can be part of the system. Follow the generator manufacturer's instructions and whatever the served agency requires, and don't assume one ground rod fixes noise or safety. Also, a long ground wire can act as an antenna at HF, so keep bonds short.

Third, for EMCOMM specifically, the checklist should include the non-radio items: a copy of the communications plan, frequencies and net procedures, ICS-style message forms, spare pens, a log, and a relief schedule for operators. Many deployments get stuck on people and paperwork rather than on hardware. A full test of the station before leaving home, including one transmit on every band and mode you might need, will find a lot of problems.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.