Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting started with LEO satellites: FM birds, linear transponders, Doppler and tracking setup

ci_cover.jpg

Starting point for a general discussion on working amateur satellites. Satellite operating looks like one hobby but is really several: FM "repeater in the sky" birds, linear SSB/CW transponders, APRS digipeaters, and the geostationary QO-100. The skills overlap, but the failure points differ. Here is a framework, with questions at the end.

FM satellites (AO-91, AO-92, SO-50, ISS voice repeater). These are the usual entry point because a single FM signal gets you through. They are cross-band: you transmit on one band and listen on another, and only one station can use the transponder at a time. That matters for etiquette. Keep exchanges short, usually a callsign and grid square, and stop when someone else is waiting. Some satellites need a CTCSS tone for access, and SO-50 in particular has an arming sequence before the repeater will respond. Satellite status, frequencies and access tones change over time, so check the AMSAT status pages and a current frequency list before a pass. Do not rely on a forum post, including this one. The same applies to whether a given FM bird is operating normally at all.

Linear transponders (RS-44, and others as they come and go). A linear transponder retransmits a whole slice of spectrum, so many SSB and CW stations can use it at once. RS-44 is a commonly discussed example with a 2 m uplink and 70 cm downlink, and it is inverting: if you tune your downlink higher, your uplink moves lower. The point is to hear your own signal in the downlink and keep it where you want it, rather than hunting for the other station. Full-duplex lets you hear yourself, which makes it much easier. Verify the transponder passband and beacon frequency from a current source before you set up memories.

Doppler shift. A LEO satellite moves at roughly 7 to 8 km/s, so the received frequency shifts through the pass. On 70 cm the swing can be around plus or minus 10 kHz or a bit under, and on 2 m about a third of that. On FM, receivers with wide enough filters hide small errors on 2 m, but the 70 cm side matters. Typical practice is to correct in steps: start high on the downlink at acquisition of signal, drop through the pass, and finish low. On the uplink you correct in the opposite direction so that the satellite receives you on the intended frequency. Software that does this (Gpredict with a rig-control interface, or SatPC32 with a supported radio) removes most of the hand-tuning. If you prefer manual operation, you can just tune the downlink while holding the uplink fixed at first, then apply corrections once comfortable.

Tracking software. Gpredict gives you pass lists, sky plots and radio and rotator control through Hamlib. SatPC32 is a Windows program popular for its tight integration with rigs and its Doppler handling. In either case, the quality of the data depends on current Keplerian elements (TLEs) and an accurate system clock. Old elements produce pass times and azimuths that drift away from reality, especially for satellites that are manoeuvred or are in a decaying orbit. Check your location settings too. A wrong Maidenhead grid square, or a latitude/longitude sign error, will make everything look plausible but be off.

Antennas. Hand-held Arrow-style dual-band Yagis, or a homemade equivalent, are a common compact setup: a few elements for 2 m and more for 70 cm on one boom. You aim by hand, often with an HT, or two radios for full-duplex. Because the satellite's polarisation as seen from the ground changes with its tumbling and orientation, fading is normal. Circular polarisation helps, as does rotating the antenna slightly. For a fixed station, crossed Yagis on an az/el rotator, with the tracking software driving it, remove the pointing workload. The limitation is more mechanical than electrical: keeping the rotator controller calibrated and cabling tidy matters more than a few extra dB of gain.

APRS via ISS. The ISS APRS digipeater is a different kind of activity. You send short packets, and the ISS may digipeat them if it is configured to do so and you are in range. The path settings you use differ from terrestrial APRS, and a station using terrestrial digipeater paths can cause problems. Check the current ISS packet configuration and operations notes from AMSAT or ARISS before transmitting.

QO-100. This one is quite different from LEO work. It is geostationary, so there is no Doppler to track and no pass to schedule, but you need a stable uplink in the 2.4 GHz band and a dish for the 10 GHz downlink. The narrowband transponder carries SSB and CW. The practical challenges are frequency stability (many users lock their LNB to a reference), keeping your uplink power modest so you don't desense others, and fitting a dish, feed and mount that don't move in the wind. Coverage is regional, so check whether your location sees the satellite at a usable elevation.

Questions to get discussion going: for someone with a handheld Arrow-style antenna and two radios, what is the most useful first skill to practise before attempting a pass? For those running Gpredict or SatPC32, what is your approach to keeping TLEs current and verifying your radio control is tuning in the right direction? And for linear birds, how do you set up a workable CW or SSB routine with Doppler correction, particularly on an inverting transponder?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the first-skill question, I'd say learn to recognise your own signal in the downlink before you worry about making contacts. Pick an easy FM pass, or listen to a linear transponder beacon, and just practise the tune-and-correct routine without transmitting. Once you know how the 70 cm side moves through a pass, calling becomes much less stressful.

For the arrow antenna, a practical tip is to use the sky plot ahead of time. Know where the satellite rises, where it culminates, and where it sets, and point the boom ahead of it rather than chasing it. With a handheld setup the common mistakes are pointing from the screen rather than from the sky, and squeezing the antenna too tightly so that you introduce movement. Also keep an eye on feedline: a short coax run and a decent connector matter more at 435 MHz than people expect.

One caution on FM birds: do not assume that because a satellite was usable last season it is usable now. Always check a current status page.

  • Moderators

On software, there are two checks I would make before trusting automatic Doppler. First, confirm the sign. Put the radio on a known beacon or a strong carrier and watch whether the program's corrected frequency moves the way the signal does. An inverted uplink on a linear transponder is where it is easiest to be wrong, and it is worth testing with low power into a dummy load or simply by watching the display before you transmit anything.

Second, confirm that the software's reference transponder entry matches the current transponder plan. A frequency database can carry old entries, and a slightly wrong centre frequency is enough to put you outside the passband. Update TLEs regularly, and make sure the computer clock is synchronised, because even a few seconds of error can change pointing slightly on a high pass.

For rotators, calibrate end stops and check the az/el offsets against a known reference such as a distant landmark. Overhead passes are harder because of azimuth flip, so many operators set the rotator to avoid wrapping across a limit mid-pass.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.