Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a remote HF station: radio-side options, VPN vs. port forwarding, latency budgets and what the rules expect

ci_cover.jpg

This thread is for comparing approaches to remote station control, from a single rig at a second QTH to a shared remote base. The basic question is how you get audio, CAT/CI-V and PTT across the internet reliably, safely and legally. Here is a rough map of the options, with some questions to start the discussion.

1. Radios with native network support. The Icom IC-7610 has a LAN port and works with Icom's RS-BA1 remote software, so the rig itself handles the network side of control and audio. FlexRadio takes this further: the radio is already a network device, and SmartSDR with SmartLink can reach it from outside the home network. Yaesu's SCU-LAN10 adds a network interface to supported models, so check Yaesu's compatibility list for your exact radio and firmware instead of assuming. In all three cases the vendor's client is the simplest path. Third-party clients such as wfview exist for some Icom radios if you want something different.

2. A small computer at the radio. A RigPi (Raspberry Pi-based) or a mini-PC running Hamlib, a sound interface, and a remote audio tool covers radios with no LAN port. It also gives you a place to run relay control, an antenna switch, a rotator, and a watchdog. The weak spot is that rigctld has no authentication. Port 4532 should never be reachable from the internet.

3. Receive-only tools as a sanity check. A WebSDR or KiwiSDR near your remote location is useful for checking whether a band is actually open, or whether your signal is getting out. They are not control systems, but they make a good second opinion on what your transmitted signal sounds like. Hosted remote-station services such as RemoteHams.com are a different model again: you use someone else's station under their access rules. Read their current terms, since I am not going to quote them from memory.

Security basics worth agreeing on. Avoid forwarding the radio's ports straight to the internet. A WireGuard or other VPN into the remote LAN, or a mesh VPN, is much safer, and the radio, Pi and PC then stay on private addresses. Put station gear on its own VLAN or at least its own subnet, change every default password, keep router and Pi firmware updated, and turn off UPnP unless you know exactly what it is opening. If a vendor's cloud relay such as SmartLink is used, it is still worth understanding what it exposes and what account security it relies on.

Latency and jitter. SSB is usually forgiving of a few hundred milliseconds of round-trip delay, though break-in and pileup work feel sluggish. CW is harder: local keying with the keyer at the radio end is often better than sending key-down events across the net. Jitter and packet loss hurt more than a steady delay, so a wired connection at both ends is worth the effort. For FT8 and similar modes, running the decoder at the radio end avoids audio-stream timing issues, and both ends should be time-synced.

Fail-safes. If the link drops while you are transmitting, what happens? A remote station should have a transmit time-out, a way to cut the carrier locally or by independent path, a remotely controllable power switch, SWR and temperature monitoring, and positive feedback on antenna and tuner state. A camera or a status page helps too.

Rules. Remote control is generally allowed, but the details depend on the country. Usually the licence requirements and band privileges of the station's location apply, there must be an identified control operator, and the station must be able to be shut down promptly. Some countries have extra requirements for automatic or unattended operation or for operating from abroad. This is a general outline, not legal advice, so check your national regulator and the licence conditions for both the operator and the station location.

Questions for the thread: Are you using the vendor client or a Hamlib-based setup? How are you handling remote access: VPN, cloud relay or port forwarding? And what is your plan if the link dies mid-transmission?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the access question, a VPN is the cleanest answer for most setups. With WireGuard or similar, the only thing exposed is the VPN endpoint, and the rig, Pi and PC just see a private address. That also solves the rigctld problem, since the unauthenticated control port is only reachable from inside the tunnel. The tradeoff is that mobile and CGNAT connections can be awkward, so a mesh VPN or a small VPS relay may be needed at the remote end.

One thing that gets overlooked is audio. Vendor clients like RS-BA1 and SmartSDR handle compression and buffering for you. If you build your own chain with a Pi and a separate audio stream, you have to tune buffer size yourself. Too small and you get dropouts on a jittery link, too large and you get a delay that makes it feel like operating through a satellite. It's worth testing in both directions over the actual path you'll use, not just on a LAN.

  • Moderators

Adding to the fail-safe point: don't rely on the same network path for both operating and emergency shutdown. A remote power switch or relay on a separate connection, such as a cellular modem or a second ISP, means you can still kill the station if the main link or a PC hangs. An ATU or amp that remembers a bad state after a reboot is another thing to plan for, because the station may come back up in a configuration you didn't choose.

On the licensing side, it's worth asking explicitly whether the control operator must be at a specific location, and what the rules say about operating a station in another country. Some regulators treat this differently from local operation, so a quick check of the regulator's published guidance, or a question to the national society, is better than assuming the home-country rules carry over.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.