Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Radio mods worth doing, mods worth skipping: MARS/CAP, expanded RX, TCXO, filters, power and noise

ci_cover.jpg

This thread is for sorting radio modifications into three groups: ones that usually improve things, ones that only help in specific situations, and ones that cause more trouble than they fix. Please share measurements and results rather than just "it works better now." Note the exact model and hardware revision when you post, because a mod that suits one board revision can be pointless or harmful on another.

Start with the boring stuff. Before opening a case, ask what problem you are solving. Many receive complaints come from front-end overload, a noisy power supply, or a bad antenna system, not from the radio itself. Many TX audio complaints come from mic gain and deviation settings, not from hardware. A modification won't fix a poor feedline or a switching supply spewing hash across the band.

MARS/CAP and out-of-band transmit mods. These are often described as "opening up" a radio. Opening up the transmitter is a different thing from being authorized to use it. In the US, MARS and CAP operate under their own programs and frequency assignments, and access to those frequencies comes from membership and authorization, not from a menu setting or a diode. Rules differ by country, so check your own regulator. Two points apply broadly. An amateur radio is not automatically approved for other services that require certified equipment. And a radio that can transmit somewhere does not mean you may. If you keep an expanded-TX radio for authorized program use, many people find it sensible to keep a separate unmodified radio for general amateur use. That makes it harder to key up on the wrong channel by accident.

Expanded receive. Software-enabled or menu-enabled wide receive is usually harmless, and it is useful for scanning, weather, public-service monitoring and similar uses. Be realistic about performance. Many handhelds have a broad front end with little selectivity outside the ham band, so strong FM broadcast, paging or TV signals can cause images, desensitization and phantom signals. If the radio gets strange when you open it up, try an external bandpass or notch filter before blaming the modification.

Filters. This is where real gains tend to show up. Narrow crystal or ceramic filters for SSB and CW can reduce adjacent-signal splatter and noise bandwidth. On VHF/UHF, a bandpass filter or an FM broadcast notch on the antenna line can cut overload. Remember that every filter adds some insertion loss, so measure it. Anything installed in the transmit path must also handle the power you run.

TCXO and frequency stability. The arithmetic is simple: 1 ppm is about 14 Hz at 14 MHz and about 146 Hz at 146 MHz. A drifty reference matters most for narrow digital modes, weak-signal work, and higher bands where the error is multiplied. A TCXO swap is only worthwhile if you can calibrate it afterward. That means a frequency counter, a GPS-disciplined reference, or at least a known-accurate signal such as WWV on HF. Confirm the part is the right frequency, voltage and output level for that board, since some radios expect a clipped sine while others want a logic-level signal.

Audio upgrades. On receive, the quickest improvement is often a better external speaker with a little filtering or DSP, and a clean audio path without ground-loop hum. For data modes, a proper discriminator or line-level tap with a correct de-emphasis/pre-emphasis path beats going through a mic jack, but you need to set levels carefully. On transmit, avoid over-deviation. A wider, louder signal is not a better signal, and a service monitor or a local station's report beats guessing.

Firmware. Read the release notes and match the exact hardware version. Back up your memory and any calibration data before flashing. Use stable power during the flash, and don't use a battery that is nearly dead. Third-party firmware can add features but may change how the radio behaves legally, since a radio's certification applies to the radio as originally sold. For anything you depend on, keep the stock firmware file and the procedure to go back.

Cooling fans. A fan can really help during long digital-mode or net transmissions on a radio that heats up. Use a thermostat or temperature-triggered fan where possible rather than a constantly running motor, and remember that fan motors can radiate noise. Airflow should draw across the heatsink, not just stir air near the case. A fan does not make up for a duty cycle the final amplifier was never designed for.

Battery and power. For base and portable stations, a LiFePO4 battery with a proper fuse close to the positive terminal and a clean DC distribution is a well-proven upgrade. Voltage sag under transmit is the usual culprit when output drops, so use thick enough wire and check connections. For handhelds, a higher-capacity pack is fine if it is protected and matches the charger. Be wary of USB-C charging mods that bypass the intended charge circuit, and don't push more voltage into a PA than the radio was designed for.

RF and noise reduction. Work from the source outward. Turn off devices around the house one by one with a battery-powered receiver nearby to find the offender. Use common-mode chokes on power leads, USB cables and coax, and put ferrites where cables enter the radio. Keep switching supplies and the antenna feedline well apart. It also helps to check the transmitter for harmonics and spurious emissions after a mod. A modified radio is still the operator's responsibility if it makes a dirty signal.

Safe practice. Use ESD precautions, take photos before disassembly, label connectors, and keep any removed parts. Test the transmitter into a dummy load before going on the air. Change one thing at a time so you know what actually helped. If you have access to a service monitor, spectrum analyzer or a well-calibrated SDR, use it to confirm frequency, deviation and spurs.

What mods have given you measurable improvement, and which ones turned out to be more hassle than benefit?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd put "measure before and after" at the top of the list. A lot of mod discussion is about feel, and radios are easy to fool you on that front. A change in volume or a different tone on the speaker is not the same as better sensitivity or selectivity. If you don't have a signal generator, an SDR with a known-stable signal, or even a repeatable weak signal on a quiet band can give you something to compare against.

On the TCXO point, the part itself is the easy half. Calibration is the half people skip. If the reference is off by a few ppm, the radio is simply wrong in a different way. On HF digital modes software can sometimes mask a small offset, but on narrow-bandwidth FM or on UHF/SHF it gets noticeable fast. Also check whether the radio actually has a calibration setting available, because without one, a swap can end up less accurate than the original.

For expanded RX, I'd add that a wide-open receiver deserves a quick sanity check against a known strong local transmitter. If a signal appears on several frequencies, you may be seeing intermodulation or images, not real activity.

  • Administrators

The legal and practical sides of modified radios deserve a more careful line than they usually get. In many places, hearing a signal is largely unregulated, and transmitting is where the rules bite. Being technically able to key a radio on a frequency says nothing about whether you hold the authorization for that service. If your radio is modified for MARS or CAP use, make sure you know what that program permits, which channels you are assigned, and what its operating rules require. Program membership is the starting point, not the radio hack.

Another point that gets overlooked: amateur gear and certified commercial or public-service gear are different categories in many jurisdictions. A radio that is approved for one purpose is not necessarily approved for another, and altering it can change that. If you want to run a radio on a repeater or in a regulated service, check the equipment requirements for that service first.

On the noise side, a cheap clip-on ferrite is not always the answer. Many noise problems come from a common-mode current path, and ferrite choice matters by frequency range. A choke that works at 7 MHz may do very little at 144 MHz. If a ferrite doesn't help, try changing where it sits (closer to the noise source) or using more turns before concluding it can't work.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.