Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a from-scratch wire antenna build: wire, insulators, feedline choke, and how much to trust SWR and models

ci_cover.jpg

I want to start a thread on the nuts and bolts of building wire antennas from raw materials. The aim is to compare approaches and sanity-check the numbers, not to argue about one best antenna. Say the goal is a 40 m dipole that can later grow into a multiband doublet, with a vertical as a second project. These are the decisions I'd like opinions on.

Starting with length: the usual formula is about 468 divided by frequency in MHz, giving feet for the whole dipole. At 7.1 MHz that is roughly 66 ft. Treat it as a starting point only. Height above ground, nearby trees, wire diameter, insulated versus bare wire, and end insulator loops all move the resonant frequency. Insulated wire usually resonates lower than bare wire, so it ends up shorter. The sensible approach is to cut long, measure, and fold back or trim in small steps. Never cut to the formula and call it done.

On wire, 14 AWG hard-drawn copper or copper-clad steel is a common choice for long spans because it resists stretching. Soft-drawn copper sags and changes length over time. Lighter wire, such as 18 AWG, is fine for short spans or portable use but gives less margin on mechanical strength. Stranded wire is easier to handle and bends without kinking. Solid wire is stiffer and can fatigue at the feedpoint if the strain relief is poor. Whatever you choose, the strain relief at the center insulator matters more than a fraction of an ohm of conductor loss.

For insulators and supports, UV-resistant polyester rope holds up better outdoors than cheap nylon, which stretches and weathers. End insulators should be rated for the tension and not crack under sun. Do not run a metal guy or halyard close to the wire ends, because the high-voltage ends of a dipole see significant RF voltage. Fiberglass telescoping poles are popular as center or end supports, but they flex under wire tension. Check clamp placement, and don't extend the top sections more than the wind loading allows.

Feedline and common-mode current are where many first builds go sideways. A dipole fed with coax is balanced at the feedpoint, but the coax shield can carry common-mode current and become part of the radiator. The result is pattern distortion, noise pickup, and RF in the shack. A current balun or choke at the feedpoint helps. One common DIY method is several turns of coax wound on a ferrite core, such as a type 43 or 31 mix toroid, or a stack of snap-on beads over the coax. The design target is high choking impedance at the operating frequency. For ladder line to a doublet, a tuner is needed, and you still need to manage common-mode current where the line enters the shack. Keep the ladder line clear of metal, and avoid running it parallel to other conductors for long distances.

For multiband, there are three typical routes. A fan dipole uses several wires from one feedpoint, but wires close to each other interact and need pruning. A trap dipole uses parallel LC traps to isolate the outer sections, which saves space but adds loss and narrows bandwidth on some bands. A doublet on ladder line with a tuner is the simplest to build and covers the most bands, but the tuner and balun do the heavy lifting, and losses depend on line length and impedance at each band.

On verticals, a quarter-wave vertical over a good ground has a feedpoint impedance around 35 ohms. Drooping the radials at about 45 degrees raises it toward 50 ohms. Ground-mounted verticals typically need a large field of radials. Elevated verticals can work with fewer radials, often four tuned ones, because the radials are the counterpoise and carry the return current. The tradeoffs are real: more radials means lower ground loss, but returns diminish and wire tangles pile up.

Finally, measurement and modeling. An antenna analyzer or a good SWR meter tells you impedance match, not efficiency. A dummy load has a perfect SWR and radiates nothing. Measure at the feedpoint if you can, or at the end of a known coax length, and note that touching the coax or moving a choke can change the reading if there is common-mode current. For modeling, EZNEC (NEC-based) and MMANA-GAL (MININEC-based) are both useful. Watch your segmentation, junction geometry, and ground model, and check the average gain test in NEC-based tools. A model is only as good as its geometry and ground assumptions.

So the questions: what are your rules for choke design and where do you put the choke? Is the fan dipole or trap route worth the trouble over a doublet? And how closely do your modeled results track the real world once you hang the wire?

  • Replies 2
  • Views 23
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the choke question, I'd separate what you're trying to achieve from how you get there. The goal is high impedance to common-mode current on the outside of the coax, and the usual rule of thumb is to aim for at least a few kilohms resistive at the lowest band. Coax coiled on a ferrite toroid is a good way to do that for HF. Type 31 mix tends to work well on the lower bands, and type 43 gets more useful as you go up. The number of turns matters because the choking impedance depends on both the core and the winding capacitance. Too many turns can lower the self-resonance, so there is a point where more turns hurts at the top bands.

A second small thing is placement. A choke right at the feedpoint is good for keeping the shield from becoming part of the antenna. A second choke at the shack entrance can help with noise, and the two do different jobs. If you are using ladder line, the line's own balance matters, so pay attention to how it leaves the antenna and stays symmetrical. A line that droops against a gutter or a pole can unbalance the system even with a decent choke.

For the fan versus trap question, I'd lean toward fan dipoles for a first build because each element is a plain wire you can trim independently. Trap antennas have more parts to fail, and traps that are not weatherproofed can drift in tuning as moisture gets in.

  • Administrators

One caution on modeling: both EZNEC and MMANA will happily give you a pretty pattern for a bad model. With a NEC-based tool, check that segments are short enough relative to wavelength and that adjacent wires at a junction have similar segment lengths. Also look at the ground type. A dipole at 10 m over real ground and the same dipole over perfect ground give very different takeoff angles and gain, so use realistic ground constants for your location rather than the default. MMANA uses a different calculation engine, so cross-checking a design in both can reveal oddities, though differences are normal near the ground and with wires that are very thick relative to segment length.

For verticals, models can mislead about radial losses unless the ground is modeled in detail. An elevated radial system is easier to model accurately than buried radials. For SWR measurements, take the reading at several frequencies across the band and plot it. A narrow dip may be a sign of a lossy trap or a bad connection. A broad, shallow SWR curve can also hide a lossy system, so don't treat low SWR as proof of a good antenna. Compare signal reports or noise floor on receive, if you can, as a rough second check.

For wire gauge, I'd say the loss difference between 14 and 12 AWG is tiny on a dipole. Mechanical choices, such as tension, UV protection, and how the wire is terminated at the insulator, are what usually determine whether the antenna survives a season.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.