Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Starting out on LEO satellites: FM birds first, then linear? Doppler, tracking software and antenna choices

ci_cover.jpg

I'm putting together a plan for getting on the satellites and want to sanity-check the order of operations. The goal is to start with FM birds (AO-91, AO-92, SO-50 and the ISS repeater if it's active), then move to the linear transponders such as RS-44 on SSB/CW once the basics feel routine. Later I'd like to look at QO-100 as a separate, no-tracking project.

Here's my current understanding. Please correct whatever is wrong.

FM birds. These are single-channel repeaters, so only one station can use one at a time. Access is typically a 70 cm uplink and a 2 m downlink, often with a CTCSS tone on the uplink. Some satellites need a specific arming tone, so check the current AMSAT status pages for tone and frequency details before each pass. Frequencies, tones and operating status change over time, and a satellite can be switched off or in a restricted mode.

Linear transponders. These retransmit a whole slice of spectrum, so many SSB and CW stations can share it. RS-44 is the one usually mentioned for LEO. Most linear birds are inverting, meaning that when your uplink goes up, the downlink goes down. Tuning is therefore less obvious than on FM, and you hear your own signal in the downlink, which is a good way to check that you're on frequency.

Doppler. As a rule of thumb the shift at 2 m is a few kHz and at 70 cm roughly three times that. That is more than enough to push an FM signal out of the passband. Mid-pass the shift crosses zero, so the correction is largest at AOS and LOS and changes fastest near closest approach.

Software. I'm comparing Gpredict (cross-platform, handles rig control through Hamlib) and SatPC32 (Windows, long-established, commonly paired with a rig interface and rotator control). Both need up-to-date Keplerian elements or TLEs, which I'll refresh regularly.

Antennas. I'm leaning toward a handheld arrow-style Yagi, either a commercial Arrow or a home-built 2 m/70 cm dual-band. I'd use a handheld dual-band for FM and possibly two radios or a satellite-capable rig for full duplex. A fixed station with a rotator and small Yagis seems like a later step.

Questions for the group:

  1. Is FM first, linear second the right order, or does jumping straight to RS-44 save time?
  2. For the first few passes, should I use manual Doppler correction or set up CAT control right away?
  3. Do I need to be exact about grid squares, and what's the best way to confirm mine? I want to exchange them correctly on the air.
  4. If I eventually fit a rotator, is azimuth-only enough for typical passes, or should I plan for az/el from the start?
  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

FM first is the usual route and I'd stick with it. The main thing it teaches you isn't Doppler, it's pass geometry: working out when the satellite is high enough to use, how to point at a moving target, and how to listen while transmitting. If you start on a linear bird, you have to deal with all of that plus inverted tuning and a very weak downlink.

On Doppler, manual tuning is a good way to learn what is actually happening. For FM, a common approach is to correct the downlink in steps as the pass progresses and leave the uplink at the nominal value for the first passes. That's good enough to start. Once you move to full duplex and linear birds, though, hand-tuning both ends gets tiresome, and CAT control in Gpredict or SatPC32 is worth the setup effort. Remember that many software setups are set up for a specific rig and may only follow one radio, so check the rig-control documentation before you buy anything.

On grid squares: they are 4-character Maidenhead locators like FN31, usually extended to 6 characters. Get yours from a locator map or from a GPS app, not from memory. On the satellites it is normal to exchange callsign and grid only, so a quick exchange is expected. Be sure you're not mixing up neighbouring squares, particularly if you are near a boundary.

For the arrow antenna, expect to move your whole body while holding it. The main skill is keeping the elements pointed at the satellite while following the track, and not dropping out of the beam when the satellite is close and fast. It is useful to print or display AOS time, maximum elevation and the azimuth of the pass before you start.

  • Administrators

Quick additions on the linear side and the rotator question.

With an inverting transponder, tune the downlink and let the radio handle the uplink arithmetic if you can. Software can maintain the relationship between uplink and downlink, so you only have one tuning knob to turn. If you tune by hand, you'll find the uplink is easy to lose while you are chasing a CW or SSB station. On CW, remember that tone and Doppler interact: if you're off by 500 Hz you won't hear the other station, and you could be sending somewhere you don't intend to. Listen to your own downlink first, and keep power low. Linear transponders are shared, and a loud station will desensitise the whole passband for everyone else. If you can hear yourself loud and clear, back off.

On the rotator: azimuth-only is workable for casual operating with a lower-gain antenna that has a broad beam, but for any Yagi with real gain, elevation matters on high passes, when the satellite goes nearly overhead and the pointing angle changes quickly. Some operators with az/el rotators still don't track through the zenith because azimuth can swing very quickly at the top of the pass. That's a known quirk of overhead passes, so check how your rotator and software deal with it, especially with a pass that goes through 90° elevation.

Don't forget polarisation. Linear antennas can fade as the satellite rotates, and the effect is more noticeable with weak signals. Circular polarisation is one common fix, and rotating the antenna slightly by hand on a handheld Yagi is another.

QO-100 is a different thing entirely. It is geostationary, so there is no Doppler and no tracking after you aim the dish once, but you need a 2.4 GHz uplink, a 10 GHz downlink and a stable LNB. Treat it as a separate project once you're happy with LEO.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.