Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

EME from 2 m to 10 GHz: what each band asks of your station (JT65/Q65, polarization, libration, skeds)

ci_cover.jpg

Here is a band-by-band breakdown of what a workable EME station looks like on 144 MHz, 432 MHz, 1296 MHz and the microwave bands, and where the practical problems usually sit. The numbers below are ballpark figures. Run your own station through a link-budget tool such as VK3UM's EMECalc before spending money on steel and aluminium.

Start with round-trip path loss, which is roughly 252 dB on 2 m, 262 dB on 70 cm, 271 dB on 23 cm and close to 289 dB on 10 GHz. That sounds like a steep penalty for going up in frequency. But antenna gain rises with frequency for a given physical size, so a dish gets you much of it back. The real work is in the details: sky and ground noise, pointing accuracy, polarization, and Doppler spread.

On 2 m the usual route is an array of long-boom Yagis, often four or more, at high power, with a mast-mounted low-noise preamp and a decent sequencer. The beamwidth is wide, so tracking is forgiving, but sky noise is high, especially when the Moon is near the galactic plane. Faraday rotation is also at its worst here. On 70 cm you can still use Yagi arrays, or a larger dish with a suitable feed. Sky noise is lower, so receive noise figure matters more, and Faraday rotation is slower and less severe.

On 23 cm a dish of roughly 3 m is a common reference size, with feed efficiency and spillover being as important as the diameter. Faraday rotation is essentially gone, but geometric polarization offset between the two stations is still a problem. On 10 GHz and above, dish surface accuracy, pointing to a fraction of a degree, and feed stability dominate. The wavelength is so short that a dish which looks fine at 1296 MHz can be useless at 10 GHz.

On the software side, JT65 is still widely used for EME. Submode A is typical on 2 m, B on 70 cm and 23 cm, and C on the higher microwave bands. Q65 has been added to WSJT-X for the same purpose, with 60-second periods and tone-spacing submodes chosen to suit the Doppler spread. Check the current WSJT-X user guide and your local band-activity conventions before settling on a submode.

Questions for the thread: what is a sensible minimum station on each band for working the big stations versus working other mid-sized stations? Where do people usually lose the most dB without realising it? And how do you set up a first sked so that it has a decent chance of success?

  • Replies 2
  • Views 25
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On minimums, it helps to separate the two goals you mentioned. Working stations with huge arrays is a different problem from working other modest stations, because in the second case both ends are weak and neither can carry the link. A smaller station can often get a first contact by choosing the right partner, while a large station on the other end adds margin without changing what you need to fix at your end.

The biggest hidden losses are usually in the receive chain. Coax loss between the antenna and the preamp adds directly to noise figure, so on 2 m and 70 cm the preamp belongs at the antenna or array, not at the shack. On 23 cm and up the preamp should be right at the feed. The relays that switch it also have loss. Sequencing is the other trap: the preamp relay must be isolated before the PA keys, and the PA must stop before the relay releases. Many preamp failures come from hot-switching, not from age.

On dishes, spillover noise and feed illumination are the two things people tend to underestimate. A feed that is too wide sees warm ground, which looks like extra system noise, while one that is too narrow wastes gain. The rule of thumb that surface errors should stay below roughly a sixteenth of a wavelength is a good sanity check. At 23 cm that is a few millimetres, which most builds can manage. At 10 GHz it is around 1.8 mm, which is much harder.

For power, the legal limit varies by country, so plan the station around what is allowed where you are, and don't assume 1 kW. Measure power at the antenna feed, after the harness, the relays and the cable, because the number at the amplifier output is not the number the array sees. With long runs of hardline, 100 W at the amp and 100 W at the feed are not the same thing.

Finally, a system check on the higher bands is to compare moon noise against cold sky, and sun noise if you have it. On 2 m the moon noise increase is too small for most stations to see, but on 23 cm and above it is a meaningful test of the whole chain, feed and dish included. If the measured number is off from what you expect, work out why before you start trying to make contacts.

  • Administrators

On polarization: the key thing is that Faraday rotation scales roughly with the inverse square of frequency. On 2 m the polarization can rotate through large angles over hours, giving deep fades when your antenna is crossed against the incoming wave. On 70 cm the effect is smaller and slower. By 23 cm it is essentially negligible. That is why 2 m stations favour cross-polarized Yagi arrays with switching or phasing, so they can select horizontal, vertical or circular, and why some use receive software that handles both polarizations at once. MAP65, for example, was built for wideband JT65 reception with cross-polarized setups.

Once Faraday rotation is out of the picture, the remaining issue is spatial polarization offset, which comes from the two stations seeing the Moon at different geometric angles. It can be large when the Moon is low at one end. Dish stations deal with it by rotating a linear feed or by using circular polarization. The convention is generally that a reflection reverses the sense of circular polarization, so stations agree on one sense for transmit and the opposite for receive. Confirm what your band uses before building a feed.

Libration fading comes from the Moon's apparent rocking motion, which creates a spread of Doppler shifts across the reflecting surface. It scales roughly with frequency: well under a few hertz on 2 m, more on 23 cm, and tens of hertz on 10 GHz. That is why the modes use wider tone spacings at higher frequencies. The fading is fast and flutter-like and is different from the slow Faraday fades. WSJT-X has an Echo tool that lets you measure your own echo and its spread, which is a helpful reference.

For sked planning, find the shared Moon window first: the Moon has to be above the horizon at both ends, ideally at a good elevation and with low sky noise. After that, agree the frequency and the transmit and receive periods. Don't assume a convention, even if one exists, because a mismatch wastes the whole window. Both stations need accurate clocks. Then settle the message sequence, including which short messages and confirmations you will use. ON4KST-style chat pages and EME mailing lists are the usual places to arrange skeds.

On tracking, beamwidth sets the requirement. Wide 2 m arrays tolerate a degree or so of error, but a 3 m dish on 10 GHz has a beam under a degree wide, so you need an accurate az/el system and an alignment you trust. Sun tracking is a good way to calibrate that alignment. Then use the software's Doppler options to keep your frequency right, whether that is correcting to your own echo or to the DX station's frequency. Both ends compensating independently is how you end up several hundred hertz apart.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.