Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio checklist: mic gain, ALC, compression, EQ and bandwidth for clean signals and weak-station work

ci_cover.jpg

This thread is a working checklist for SSB audio, from the microphone to the passband. Most reports of "harsh", "splattery" or "hard to copy" audio trace back to a few settings that interact: mic gain, processor level, ALC, and EQ. Please add corrections or radio-specific notes.

Sideband convention. Use LSB on 160, 80 and 40 meters and USB on 20 meters and up. On 60 meters, USB is the convention, and in the US it is effectively required by the channelized rules. If you call someone on the wrong sideband, they will hear inverted, unintelligible audio, and the mistake is easy to make while tuning around.

Start with the microphone and the room. No setting fixes a bad pickup. Keep the mic roughly a few finger-widths from your mouth and consistent. Speaking slightly across the capsule, or using a foam windscreen, tames plosives. Room echo and fan noise get amplified along with your voice, and a compressor raises them further. Choose a mic for a narrow, speech-focused response. A wide-range studio condenser mostly wastes its extra bandwidth on SSB and picks up more room noise.

Set mic gain by ALC, not by feel. With the processor off, speak at normal volume and adjust mic gain so the ALC meter only moves on the loudest peaks, within the range your manual specifies. ALC pinned at the top of the scale means the audio chain is overdriven. That produces flat-topping, distortion and a wider, dirtier signal. ALC is a protection circuit, not a loudness control. Drive that overshoots it makes the signal worse, not louder.

Processor and compression. A speech processor raises average power relative to peak power, which is why it helps in a weak-signal or pileup situation. Light settings, in the low single-digit dB range of compression on most meters, usually improve readability. Heavy compression brings up background noise, makes sibilance harsh and adds distortion products that widen the signal. If you can hear your own audio sounding pumped or crunchy, back it off. When in doubt, use less than you think you need.

Equalizer. Most voices benefit from cutting the very low end, since energy below about 200 Hz adds little intelligibility and costs power. A modest lift in the 2 to 3 kHz area can help clarity. Be careful with big boosts: they add sibilance and make the processor work harder. Because a standard SSB passband only goes up to about 2.4 to 2.7 kHz, a "bright" boost at 4 kHz or above accomplishes nothing on the air.

Monitor. The monitor function lets you hear your transmit audio through headphones, which is good for spotting distortion, hum and processor overload. But it is usually taken from a point inside the radio, so it won't tell you everything about what leaves the antenna. An independent check is better: a second receiver, a WebSDR or remote receiver, or a trusted local station who will give you honest feedback.

Bandwidth and filters. A 2.4 kHz transmit and receive width is a good general compromise. Many newer radios let you set TX bandwidth (wide, mid, narrow). Wider settings sound more natural for ragchews on quiet bands. Narrower settings concentrate power and occupy less spectrum on a crowded band or in a pileup. On receive, you can often go below 2.4 kHz: 1.8 to 2.2 kHz can improve copy on weak or noisy signals, since it cuts noise and adjacent-channel splatter. Use passband shift or IF shift to move away from interference.

Working weak stations and DX. Start with a clean receiver setup. On the lower bands, turn off the preamp if the noise floor is already high, and reduce AF gain so your ear is not fatigued by noise. Use noise reduction in moderation, since heavy DSP reduction can make weak speech sound watery. Try the notch for carriers. When calling DX, listen to where the DX station is listening, particularly in split operation. Keep calls short, say your callsign clearly once or twice with standard phonetics, and don't overdrive your amplifier. A clean 100 watts usually beats a splattering kilowatt.

Quick sanity checks. Check for RF in the shack with the microphone connected: a ferrite choke on the mic cable and good grounding help. Watch ALC on the amplifier too, if it has one. And record yourself: hearing a recording often reveals issues that the live monitor hides.

What are your preferred starting values for compression and EQ, and do you adjust them between ragchewing and DX work?

  • Replies 2
  • Views 24
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

A useful addition: treat the ALC reading as a ceiling, not a target. Some radios show ALC only on the transmit path before the final amplifier stage, so a meter that looks fine doesn't prove your output is clean. If you run an amplifier, set drive so the amp's ALC shows little or no action and the output follows the exciter linearly. A common mistake is to boost compression to "get more out of the amp" and end up with a signal wide enough to bother neighbors up and down the band.

On processors, it helps to test in steps. Turn compression off, say a few words, then raise it a bit at a time while watching the meter and listening on a monitor or second receiver. When the compression meter shows a few dB on peaks, stop and check for pumping on breaths and pauses. If room noise rises in the gaps, you've gone too far or the mic is too far away.

  • Moderators

On filters, there's a trade-off. A 2.4 kHz receive filter is a good default, but if the band is busy and the weak station has an adjacent strong one, narrowing to around 1.8 to 2.0 kHz may help more than any noise reduction. The voice will sound duller, but it is often more readable because the interference is lower. Try shifting the passband too: with LSB or USB, the low-frequency edge often has more effect on how "boomy" a voice sounds, while the high edge affects clarity and sibilance.

For DX, a flatter, lightly processed signal with the low end cut generally gets through better than one with a lot of boosted treble. If you hear that a strong station near you is wide, don't copy the sound, copy the habit: check your own signal with a receiver or SDR, because splatter is easier to see on a waterfall than to hear on your monitor.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.