Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a first homebrew QRP station: what to build in what order, and which test gear is worth having

ci_cover.jpg

I'd like to get a sensible build order down for someone starting a homebrew QRP station from scratch, and I'd like to hear where people disagree. The idea is to build the pieces so each one is testable on its own and the later ones aren't wasted effort.

Here is the order I would propose. Start with a 50 ohm dummy load and an RF probe for the DMM. Next, a small crystal-controlled transmitter such as a Tuna Tin 2 style 40 m oscillator/PA, which makes roughly a quarter of a watt. After that, a direct conversion receiver. Then a low-pass filter and an SWR bridge. Only after those would I move on to a full transceiver, whether a BITX-family design or a kit, and then an amplifier.

The reasoning goes like this. A Tuna Tin 2 is simple enough that when something fails you can find the fault with a multimeter and a scope. Into a 50 ohm load, 250 mW is about 3.5 V RMS, or around 10 V peak to peak. If you see 4 V peak to peak, you know the stage is working but is not delivering what the schematic promises. That kind of check teaches you more than any amount of reading. The Pixie is similar in spirit, but its single transistor doing both transmit PA and receive detector duty makes it a poor receiver. It is fun as a curiosity but a bad yardstick for judging your own building.

A direct conversion receiver is the next logical step because it covers most of the receiver fundamentals in few parts: a front-end bandpass filter, a product detector (diode ring, NE602/SA612 or similar), a stable VFO or synthesizer, and a high-gain audio chain. It also teaches the classic problems: AM broadcast breakthrough, microphonics in the VFO, hum, and the lack of sideband rejection, so you hear both sides of zero beat.

Where I expect disagreement is the test gear. My short list is a DMM, a 20 MHz or better scope, a dummy load and an RF probe, a frequency counter or a calibrated receiver, and a NanoVNA-class analyzer for filters and antennas. Is there something on that list you would drop, or something you would insist on adding before building anything?

Related questions I'd like to settle in this thread: should a first-time builder use Manhattan or dead-bug construction on bare copper-clad board, or buy kits with silkscreened boards? And at what point does a 13.8 V supply need current limiting for bench testing?

  • Replies 2
  • Views 24
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The order makes sense to me, and I'd put the low-pass filter earlier, ideally before the transmitter ever sees an antenna. A single-transistor crystal oscillator with a pi-network output is not a clean source. A 5-pole low-pass filter cut for the band, with a reasonable Chebyshev or Butterworth design, is small and cheap. Rules on spurious emissions differ by country and power level, so check what applies to you rather than assuming a QRP signal is automatically clean.

On direct conversion receivers, the AM broadcast breakthrough you mentioned is usually a front-end problem rather than a detector problem. A bandpass filter ahead of the mixer, or at least a high-pass that rejects the medium wave band, often does more than any tweaking after the mixer. Putting a low-pass or simple active filter in the audio path also helps, since a direct conversion receiver passes everything from near DC to the top of the audio range. For CW, a narrow audio filter centered around 600 to 700 Hz makes a bigger practical difference than almost any RF change.

On the dummy load, the 7.07 V RMS across 50 ohms per watt is worth having written on the bench. A quick scope check on the load gives you a power estimate before you trust any home-built meter. That ties into the SWR bridge: calibrate it with a known 50 ohm load first (it should read near zero reflected), then with an open and a short, and see that it behaves sensibly. A bridge that has never been checked against known mismatches can give you false confidence.

  • Moderators

On kits versus scratch building, I'd say a kit is the better first project if the goal is a working transceiver, and a scratch-built project is better if the goal is to learn how the circuit works. The two aren't exclusive. Building a kit is still soldering practice, and a good kit manual forces you to measure things at each stage. Where a kit goes wrong is when you skip those measurements and just keep stuffing parts.

The BITX family is a good example of a design worth studying even if you never build one. Its bidirectional amplifier stages, the diode ring mixers, and the crystal ladder filter at the intermediate frequency are all ideas you can reuse. The uBITX moved the oscillator duties to a microcontroller and a Si5351 clock generator, which gives you multiband coverage in a small package. The tradeoff is that synthesizer-based designs can produce spurs and harmonics that a simple analog VFO wouldn't, so verify the output with a spectrum analyzer or a second receiver, and think about the low-pass filter set and the drive levels. Treat any stated output power as a figure to verify on your own bench.

For the power supply question, I'd always use current limiting for first power-up of any new board. A bench supply with a current limit set a bit above the expected draw is ideal. Without one, a series resistor or a small automotive bulb in the supply line is a cheap substitute. Add reverse polarity protection (a diode in series or a diode across the input with a fuse) because a backwards connection is one of the more common ways to ruin a finished kit.

For construction style, Manhattan pads and dead-bug on a solid ground plane work well at HF and keep stray capacitance and lead length under control. Silkscreened boards are easier for the first build, but learning to build on bare board is worth it once the basics are solid, since many homebrew designs are only published as schematics.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.