Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Field station layout for a 24-48 hour deployment: what order do you set up power, antennas and noise control?

ci_cover.jpg

I'd like to compare approaches to the setup order for a field station that has to run a day or two unattended by a power grid. This could be an EMCOMM served-agency support position, a shelter or EOC backup, or a remote relay point. The gear list is the easy part. The sequence is where stations tend to lose hours: the antenna goes up before the noise floor is known, the generator ends up upwind of the tent, or the battery bank turns out to be half the size the load needs.

Here is a baseline for people to pick apart.

Start with the power budget, not the battery. A 100 W HF rig on SSB can pull roughly 20 A or more at 13.8 V on voice peaks, but the average over a voice or digital net is much lower, and receive current is often only 1 to 2 A. Digital modes at high duty cycle are the exception, so derate the power or plan for the real transmit percentage. Add the VHF/UHF radio, laptop, tablet, charging for handhelds, lighting, a router or hotspot if the served agency needs one, and any fans or heaters. Convert the total to amp-hours per 24 hours and add margin. Nameplate amp-hours on a LiFePO4 pack are also not the whole story, because the BMS limits, cold-weather charge cutoffs and inverter losses all eat into it.

Generator placement comes next. Inverter generators put out clean enough power for most radio gear, but CO is the real hazard, not RF. Keep the unit well away from the tent or shelter and downwind, with the exhaust pointed away from any opening, and never run it in an enclosed space. Treat the generator as a charger for the battery bank rather than the primary supply, so the radios keep running while it is shut down for refueling or quiet hours. Use GFCI protection on AC distribution, and follow the manufacturer's instructions on grounding and bonding for that specific unit.

On the DC side, I'd put a fuse or breaker close to the battery terminal on every positive leg, size the wire for the fuse and not the other way around, and use one connector standard across the whole kit. Powerpoles are common for this, but the polarity and orientation convention matters more than the brand, so your group should pick one and label it. A distribution block with individually fused outputs makes failures local. Run the radios from a distribution point that is not also feeding noisy loads like cheap USB chargers.

For antennas, the mission should drive the choice. For regional HF coverage, a low horizontal dipole or inverted-V at NVIS heights on 80 or 40 m is often more useful than a tall vertical. For VHF/UHF, height and low-loss coax matter more than the antenna model. The mast should be non-conductive or well guyed, with a defined fall zone clear of power lines, vehicles and people. A rule of thumb is that nothing within the mast's falling radius should be anything you cannot afford to lose.

Coax runs deserve a loss calculation. A short run of thin coax is fine on HF, but on 2 m and 70 cm the loss over a long run can cost more signal than a better antenna would gain. Put a common-mode choke at the feedpoint and consider another at the radio, then secure the cable so wind and foot traffic cannot pull on connectors.

Finally, noise. Before transmitting, listen on the bands you plan to use with the generator, chargers, solar controller and lighting all running, then switch things off one at a time. MPPT solar controllers, LED lighting, laptop supplies and USB cables are frequent offenders. Ferrites, separation, and moving the antenna away from wiring harnesses fix more problems than people expect.

Questions for the thread: what order do you use for setup? Do you test noise before or after the antenna is at full height? And how do you handle the sizing question when the served agency changes the requirements mid-deployment?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd do the noise survey earlier than the post suggests. Put the receive antenna up at a temporary low height first, with every power source and accessory running, and look at the S-meter or an SDR waterfall before committing to the full mast. If the generator or a charger is raising the floor on 40 m, it is much cheaper to move a power cord or swap a charger now than to relocate the antenna after it is guyed.

On LiFePO4, check three things before the event. First, charge termination voltage: most packs expect about 14.2 to 14.6 V, so make sure the generator charger and the solar controller are both set to a LiFePO4 profile and not an AGM one that might overcharge or undercharge. Second, cold: many BMS units refuse to charge below freezing, which can leave you with a bank that discharges fine but won't accept solar. Third, the BMS current limit: a pack rated for continuous 100 A is fine for a 100 W rig, but if you add an inverter, check the surge rating too.

One more small point: with a LiFePO4 bank, voltage is a poor gauge of state of charge because the curve is so flat. A shunt-based monitor is worth having so you know how much capacity is left when the sun disappears or the generator runs out of fuel.

  • Administrators

Agreed on the mission driving the antenna. For EMCOMM, I'd also separate the "primary" and "backup" paths on purpose: one HF antenna that covers the regional net, and a simple VHF/UHF setup that still works if the HF mast comes down in wind. A roll-up J-pole or a small vertical on a short mast takes minutes to deploy and covers local simplex or repeater traffic while the larger antenna is being built.

For the tent, keep the radios inside but keep the feedlines and antennas outside with a defined cable entry, such as a gap in a wall flap, with a drip loop so water does not run along the coax into the shelter. Metal-framed pop-up canopies can couple to nearby antennas, so keep wires and verticals away from the frame and check SWR with the canopy in place, not just before it goes up. Stakes and weights matter as much as the radio gear, since an unsecured canopy in gusts is a hazard to people and antennas.

On grounding, I'd separate the ideas. Bonding the radios, power supply and any metal chassis to a common point reduces shock risk and some noise. A ground rod does not make a station safe from lightning. If thunderstorms are anywhere nearby, the plan should be to stop transmitting, disconnect the feedlines, lower the antennas if that can be done safely, and move people to proper shelter.

For teardown, I'd write the checklist in reverse order of setup: power down radios, disconnect antennas, lower masts, coil coax in a way that matches how it unrolls, then count stakes, guy lines and connectors against the packing list. Missing small items like adapters, spare fuses and Powerpole crimp tools are the usual losses, so I'd keep a printed inventory in the kit itself.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.