Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a wire dipole from scratch: wire, feedpoint, choke, ladder line, and how far to trust SWR and models

ci_cover.jpg

I'd like to collect practical build guidance in one thread for people making wire antennas from raw materials instead of buying kits. Here is a hypothetical project to anchor the discussion: a 40 m dipole that can later grow into an 80 m-capable doublet, fed either with coax and a choke or with open-wire or windowed ladder line to a tuner. Many details apply equally to verticals and trap designs.

Starting numbers. A half-wave dipole is roughly 468 / f(MHz) feet overall, so about 66 ft at 7.1 MHz, or about 33 ft per leg. A quarter-wave vertical is roughly 234 / f(MHz), about 33 ft at 7.1 MHz. These are starting points only. Height above ground, nearby conductors, wire diameter, insulation, sag, and the end insulators all move the resonant frequency. Plan to cut long and trim.

Wire. Hard-drawn solid copper is strong but kinks easily. Stranded copper is easier to handle, but soft-drawn stranded wire stretches over time. Copperweld (copper-clad steel) is very strong and resists stretching, which helps on long spans. Insulated wire usually resonates a few percent lower than bare wire, so the legs end up a little shorter. For HF, 14 AWG is a common compromise, with 12 AWG for longer spans or harsher weather, and thinner wire where the span is short and supported along its length.

Hardware. Use UV-resistant insulators such as glazed ceramic, HDPE, or purpose-made plastic, and UV-stable polyester rope. Nylon stretches, and natural fiber rots. Put strain relief at the feedpoint so the coax or ladder line weight doesn't pull on soldered joints. At the center, a 1:1 current balun or a coax choke keeps common-mode current off the feedline. For ladder line, the usual advice is to keep it away from metal and to route it away from the antenna at a right angle. Avoid tight bends and twist it only gently.

Questions for the thread:

1. How much choking impedance is enough? Is a coil of coax good enough, or should ferrite (mix 31, mix 43, or stacked beads) be the default?

2. When is a resonant coax-fed dipole better than a non-resonant doublet with ladder line and a tuner?

3. For verticals, how many radials are really needed, and does it matter whether they are on the ground or elevated?

4. How do you check an antenna's performance when SWR at the shack end can hide feedline loss?

5. EZNEC versus MMANA-GAL: which assumptions in each tend to mislead beginners most?

  • Replies 2
  • Views 23
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the choke: the goal is a high common-mode impedance at the operating frequency, ideally in the thousands of ohms, so the coax shield doesn't become part of the antenna. A coil of coax can work, but it's narrowband and self-resonant, so the number of turns and the coil diameter need to be matched to the band. For multiband use, ferrite is easier to get right. Mix 31 is generally favored for lower HF, mix 43 for the upper bands, and stacking several cores on the coax raises the impedance. A choke at the feedpoint and a second one a quarter wave or so down the coax is a common approach on a dipole. At high power or high SWR, heating in a marginal ferrite choke is real, so don't choose the smallest core that technically fits.

A quick way to see whether common-mode current is a problem: watch whether the SWR or the analyzer reading changes when you move the coax, touch the shield, or add a few feet of cable. If it does, the feedline is radiating or picking up. This isn't a measurement of choke impedance, but it is a good practical warning sign.

For resonant versus non-resonant: a coax-fed dipole cut for one band is simple and efficient. A doublet of about 130 to 135 ft fed with ladder line and a tuner covers many bands, but the tuner and any balun at the tuner become part of the system. Use a good current balun there, and remember that the ladder line itself is low loss even when the SWR on it is high. The balun and tuner can be where the loss is.

For trimming: build the dipole 3 to 5 percent long, hang it at its final height and shape (an inverted-V with a 90 to 120 degree apex will lower the feedpoint impedance), then shorten both legs by equal amounts while watching the analyzer.

  • Moderators

Radials are where verticals most often go wrong. A ground-mounted quarter-wave vertical depends on the radial field to return current, so the number matters a lot. Efficiency generally improves as you add radials. A field of 16 is often considered a reasonable minimum, and many more will do better. Elevated radials behave differently. Because they are above lossy soil, a few resonant radials, often 2 to 4 cut near a quarter wavelength, can work well, and adjusting their angle or number can bring the feedpoint closer to 50 ohms. Poor radials won't necessarily show up as high SWR. A lossy vertical can show a good SWR and still be a weak radiator, which is why SWR isn't a quality measurement.

For fiberglass poles: telescoping poles are light and cheap, but they need guying, hose clamps or tape at the joints, and a wire routed down the pole that won't slide. Keep any pole well away from power lines.

On traps: a parallel LC trap isolates the part of the wire beyond it at its resonant frequency, which lets one antenna work on multiple bands. The trade-offs are narrower bandwidth, some added loss, and a shorter overall length. If you homebrew them, confirm the trap resonance with an analyzer before it goes on the antenna, because capacitor tolerance and coil stray capacitance shift it. A fan dipole is simpler to build and repair, but interaction between the elements still means some trimming.

For measuring SWR: measuring at the transmitter includes the coax loss, which can make a poor antenna look better than it is. A NanoVNA or antenna analyzer at the feedpoint gives a better picture, and it should be calibrated at the end of the cable you are using.

For modeling: both programs are useful, but a model is only as good as its inputs. Check segmentation, junctions, wire radius, and ground type. EZNEC is NEC-based, MMANA-GAL has a different calculation core, and both are sensitive to wires close to ground. A sensible habit is to model the antenna, build it, and compare the real analyzer measurements against the prediction. Differences tell you what you didn't account for, such as nearby trees, sag, or the feedline. Check the current segment limits of the EZNEC version you use before planning a detailed model.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.