ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
First repeater programming checklist: offsets, tones, linking modes and etiquette
This thread is meant as a practical reference for anyone programming a first repeater channel, or for people who have used repeaters for a while and keep running into linked systems they don't fully understand. Please add corrections and local differences, because repeater conventions vary a lot between regions.
The basic requirements for working a standard analog FM repeater are the output frequency (what you listen to), the offset and its direction (which sets the input frequency you transmit on), and any access tone. A repeater with an output of 146.940 MHz and a -600 kHz offset listens on 146.340 MHz. Common offsets depend on the band and country. In North America, 2 m is usually 600 kHz and 70 cm is usually 5 MHz, with the direction set by the band plan segment. In other regions the numbers differ, for example 1.6 MHz on 70 cm in the UK. Check your local band plan and a current directory listing instead of assuming.
The tone is where many first attempts go wrong. CTCSS (often called PL, after Motorola's trademark) is a continuous sub-audible tone between roughly 67 and 254 Hz. Most repeaters require your radio to transmit that tone before they will open. Some also send a tone on the output, which you can use for tone squelch on receive. DCS is a digital alternative using three-digit codes, with normal and inverted polarity. Tone settings are not security. They only help the repeater and your receiver ignore unwanted signals. Radios usually offer separate settings for encode only, encode and decode (tone squelch), and DCS, so make sure you are setting the one the repeater needs.
A quick diagnostic: if you hear the repeater clearly but it never responds when you key up, suspect the input tone or the offset direction first. If you hear it but can't hear anyone who clearly talks to you, check whether tone squelch on receive is muting them. And if you can hear the other station on the repeater input when you press the reverse button, you may be able to talk simplex and leave the repeater free.
What other settings or listings have caused confusion for newcomers? And are there regional conventions that people should know before they transmit?
This thread is meant as a practical reference for anyone programming a first repeater channel, or for people who have used repeaters for a while and keep running into linked systems they don't fully understand. Please add corrections and local differences, because repeater conventions vary a lot between regions.
The basic requirements for working a standard analog FM repeater are the output frequency (what you listen to), the offset and its direction (which sets the input frequency you transmit on), and any access tone. A repeater with an output of 146.940 MHz and a -600 kHz offset listens on 146.340 MHz. Common offsets depend on the band and country. In North America, 2 m is usually 600 kHz and 70 cm is usually 5 MHz, with the direction set by the band plan segment. In other regions the numbers differ, for example 1.6 MHz on 70 cm in the UK. Check your local band plan and a current directory listing instead of assuming.
The tone is where many first attempts go wrong. CTCSS (often called PL, after Motorola's trademark) is a continuous sub-audible tone between roughly 67 and 254 Hz. Most repeaters require your radio to transmit that tone before they will open. Some also send a tone on the output, which you can use for tone squelch on receive. DCS is a digital alternative using three-digit codes, with normal and inverted polarity. Tone settings are not security. They only help the repeater and your receiver ignore unwanted signals. Radios usually offer separate settings for encode only, encode and decode (tone squelch), and DCS, so make sure you are setting the one the repeater needs.
A quick diagnostic: if you hear the repeater clearly but it never responds when you key up, suspect the input tone or the offset direction first. If you hear it but can't hear anyone who clearly talks to you, check whether tone squelch on receive is muting them. And if you can hear the other station on the repeater input when you press the reverse button, you may be able to talk simplex and leave the repeater free.
What other settings or listings have caused confusion for newcomers? And are there regional conventions that people should know before they transmit?
Link to comment
https://www.hamradiobase.com/forums/topic/11590-first-repeater-programming-checklist-offsets-tones-linking-modes-and-etiquette/Share on other sites