APRS on 144.390: how the pieces fit together (digipeaters, iGates, Mic-E, SmartBeaconing, Direwolf and handhelds)
- Replies 2
- Views 31
- Created
- Last Reply
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
APRS gets confusing because it is several things at once: a packet format, a shared simplex channel, a network of digipeaters, an internet backbone, and a set of conventions for objects, messages and weather. This thread is meant to lay out how the pieces connect and to collect practical settings. Corrections are welcome, especially for regional differences.
The RF side. In North America, APRS runs on 144.390 MHz using 1200 baud AFSK with AX.25 UI (unconnected) frames. Other regions use different frequencies. 144.800 MHz is common in Europe and Africa, and Japan and Australia each have their own. Check your local band plan before programming a radio. Everyone shares one channel and nobody acknowledges position packets, so airtime is the scarce resource. That is the reason for the advice about beacon rates and path length.
Digipeaters and paths. A digipeater repeats a packet if its path contains an alias the digipeater answers to. The common mobile path is
WIDE1-1,WIDE2-1. WIDE1-1 is picked up by a nearby fill-in digi, usually a low-site or home station. WIDE2-1 is then used by a wide-area digi. Each hop decrements the SSID, and the digipeater inserts its own callsign and marks it as used. Long paths such as WIDE7-7 flood the channel and are discouraged in most areas. Fixed stations with good coverage often use WIDE2-1 or WIDE2-2, or no path at all. Local convention varies, so ask nearby digipeater operators what they recommend.iGates. An iGate receives RF packets and forwards them to the APRS-IS servers over the internet. This is how aprs.fi and similar sites get their data. Logging in needs your callsign and an APRS-IS passcode. A receive-only iGate is the simplest and least risky setup. A TX iGate sends certain internet traffic back to RF, mainly messages to stations recently heard locally. It should be configured carefully so it does not add traffic or create loops. Packets with TCPIP, NOGATE or RFONLY in the path should not be gated to the internet.
Direwolf. Direwolf is a software TNC. It uses a sound card or USB audio interface as the modem and can act as a digipeater, an iGate, or a KISS/AGW TNC for other software. The configuration lives in
direwolf.conf. The key lines areADEVICEfor audio,MYCALL,MODEM 1200,PBEACONfor your own beacon,DIGIPEATto enable digipeating, andIGSERVERwithIGLOGINfor the internet connection. By default it offers KISS over TCP on port 8001 and AGW on 8000. Most problems come from audio levels and PTT control rather than from the configuration file, so use Direwolf's own audio level reports to set the input level.Handhelds. The Kenwood TH-D74 and TH-D75 have a built-in TNC and GPS and can beacon, digipeat, and send and receive messages without a computer. They can also act as a KISS TNC over USB or Bluetooth for other software. The Yaesu FT5D has built-in GPS and APRS as well. The menus differ between radios, and the beacon, path and Mic-E or standard-format settings are easy to misconfigure. Read each manual and check what your own packets look like on aprs.fi.
Mic-E and SmartBeaconing. Mic-E is a compact position encoding. Part of the latitude is carried in the destination address field, and the information field holds longitude, speed and course. It also includes a status code such as In Service or Emergency. It is efficient for mobile use, so many radios use it by default. SmartBeaconing varies the beacon interval with speed and heading changes. The main parameters are fast speed and fast rate, slow speed and slow rate, minimum turn time, minimum turn angle, and turn slope. The aim is frequent beacons when you are moving fast or turning, and infrequent ones when you are slow or stopped.
Objects, messages and weather. Objects represent things other than the transmitting station, such as an event, a storm, or a repeater location. They have a name of up to nine characters and are sent with a timestamp and position. Messages go to a specific addressee, are limited to about 67 characters of text, and use a message number so the receiver can acknowledge. Weather stations send position plus weather data, usually with the weather station symbol, at intervals of several minutes. Excessive reporting should be avoided.
Questions for the thread: what paths and beacon intervals are working in your area, and what settings have you found sensible for SmartBeaconing on the D74/D75 or FT5D?
Link to comment
https://www.hamradiobase.com/forums/topic/11599-aprs-on-144390-how-the-pieces-fit-together-digipeaters-igates-mic-e-smartbeaconing-direwolf-and-handhelds/Share on other sites