Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Field station planning: power, antennas and noise control, and what order do you set things up in?

ci_cover.jpg

I'd like to compare notes on a repeatable setup for a field or EMCOMM station: a tent or canopy, one HF rig, one VHF/UHF rig, and a few hours to a couple of days of operation. Gear lists are easy to find. The hard part is the order of operations and where a plan usually breaks. Here's a framework to poke holes in.

Power first, because everything else depends on it. The two common architectures are an inverter generator feeding a charger or supply, or a LiFePO4 battery as the main bus with the generator and solar as chargers. The second tends to be quieter, both acoustically and in RF, because the radios run from DC and the generator can sit far away or stay off. LiFePO4 holds roughly 13 V under load for most of its discharge curve, which suits 13.8 V-nominal rigs, but the BMS can cut off abruptly at low state of charge. A rig that was running fine just disappears. Watch battery monitoring (a shunt-based meter beats a voltage reading) and set your own cutoff above the BMS limit.

Distribution. One fused feed from the battery to a distribution block with individual fuses per branch is the usual approach, with Anderson Powerpoles as the common connector standard in ham circles. Size wire for the fuse, not just the load, and calculate voltage drop on longer runs. A 20 A branch on thin wire can sag enough to make an HF rig distort on transmit peaks, which people often misdiagnose as an antenna or audio problem.

Antennas. For regional HF work, a low dipole or inverted V on a fiberglass pole is hard to beat for simplicity, and low heights suit NVIS on 40 and 80 m. For VHF/UHF, the coax is often the weak point: a long run of RG-58 can eat a large fraction of your power at 2 m and 70 cm, so check the manufacturer's loss figures and consider a lower-loss cable or moving the radio closer to the mast. Put a common-mode choke at the feedpoint and another where the coax enters the shelter.

Noise. I'd treat noise hunting as part of setup rather than troubleshooting afterward. Tune to a quiet spot on 40 m or 20 m, then power up each device one at a time: charge controllers, laptop chargers, LED lanterns, USB hubs, switch-mode supplies. Whatever raises the noise floor either gets a ferrite or moves away from the antenna, or gets turned off.

Questions for the group. What do you set up first when daylight is limited? How do you decide generator placement relative to the operating position? And what do you do about grounding, which is where I see the most confident-sounding advice with the least agreement?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On order of operations, a sequence that holds up is: safety and site layout, then power, then antennas, then radios, then a noise check, then a communications check. The site layout step gets skipped most. Before anything is unpacked, decide where the generator goes (downwind and well away from the tent and any air intake, never in or under the shelter), where the mast goes, and where the coax and power lines will cross walkways. Carbon monoxide is the hazard that actually hurts people at field sites, so a battery CO alarm inside an enclosed shelter is cheap insurance even when the generator is outside.

On the generator question: with a LiFePO4 bus, the generator becomes a charging tool. Run it, fill the battery through a proper charger or DC-DC source, shut it down, and operate quietly. That cuts fuel use, noise and RF hash, and it also makes it simpler to stay on frequency during net traffic. If you need AC for a charger, check that it tolerates the generator's output and doesn't hunt when the load is small.

Solar is more useful as a trickle supplement than a primary source unless the panels are big. Use an MPPT controller with a LiFePO4 profile, and note that LiFePO4 shouldn't be charged below freezing unless the battery has low-temperature protection or heating. Test the controller with your receiver on HF before trusting it, since some are noisy and the fix may be ferrites on both the panel and battery leads, or simply moving the controller.

On grounding: for personal safety, make sure the generator is used per its manual and that any AC equipment is on GFCI protection. For RF, a ground rod rarely fixes an HF noise problem. If the antenna is a dipole with a good choke, common-mode current is usually the real issue. Also, nothing about a field antenna is lightning-safe, so the plan is to take it down and disconnect coax when a storm is approaching, not to rely on a rod.

  • Administrators

Adding to the antenna and shelter side, because mast failures and cable problems cause a lot of avoidable trouble.

Mast placement: keep it well clear of power lines, with a distance of at least the mast height plus a generous margin, and don't set one up at all if you can't guarantee that. Guy a fiberglass mast at more than one level if the manufacturer allows it, use stakes that suit the soil, and flag the guy lines so people don't trip. For canopies, weights are what keep them from becoming a kite in a gust. Lighter fabric is useful but only if you secure it properly, and many people simply lower the canopy when wind picks up.

Coax: leave a drip loop where the cable enters the shelter, add strain relief at the radio, and don't let connectors sit in puddles. Label both ends of every cable with its function, because at 2 a.m. in the rain 'the other black coax' is not a useful description. Cable ramps or a covered channel protect lines where foot or vehicle traffic crosses.

An EFHW is popular for fast deployments, but it behaves best with a real choke at the transformer and a considered counterpoise, otherwise the coax becomes part of the antenna and noise and RF in the shack show up. A center-fed dipole with a 1:1 choke is more forgiving. Either way, check SWR and then listen: a low SWR doesn't prove the antenna is efficient.

For a teardown checklist, reverse the setup but add a few items: confirm every stake and weight is recovered, inspect connectors and coax for damage before they go back in the bin, charge or storage-charge batteries according to the manufacturer's guidance, and note anything that failed so it gets fixed before the next deployment. A short list taped inside the lid of each case, with the failure points you've found, will beat a long document nobody opens.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.