Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Band plans vs. FCC rules: where do you actually operate, and how close to the band edge is safe? (160 m through 33 cm)

ci_cover.jpg

Question for the group, mainly for newer licensees and anyone who has only used a few bands so far. I'm trying to sort out the difference between what the FCC requires and what the ARRL band plan only recommends. Once I move past a single repeater or one FT8 frequency, the whole thing gets confusing.

The specific points I'd like laid out:

1) For 160 through 10 meters, how are CW, digital and phone segments divided, and which parts are rules and which are convention? 2) How should I think about operating near a band edge, especially with SSB? 3) What are the 60 meter channels and how do they differ from every other HF band? 4) For 6 m, 2 m, 70 cm and 33 cm, what are the simplex calling frequencies and the common weak-signal spots? 5) How do privileges break down by Technician, General and Extra? 6) What changes internationally if I travel or work DX?

Corrections are welcome. I'd rather get this right than repeat folklore. Everyone should also check the current Part 97 text and the current ARRL band plan, since both get revised.

  • Replies 2
  • Views 43
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the rules-versus-plan split, because it answers a lot of the rest. Part 97 (mainly 97.301 through 97.305) is the law. It sets which bands each license class can use, which emission types are allowed in which segments, and power limits. The ARRL band plan is voluntary. It tells you where the community has agreed to put FT8, SSB, beacons, DX windows and so on. Nobody owns a frequency, and you are expected to share, but ignoring the plan makes you the person stepping on a weak-signal net.

On HF in the US, the phone/CW divisions are mostly written into the rules for General and Technician, with Extra getting the widest slices. Rough General-class numbers: 80 m CW/data 3.525-3.600 and phone 3.800-4.000. 40 m CW/data 7.025-7.125 and phone 7.175-7.300. 20 m CW/data 14.025-14.150 and phone 14.225-14.350. 15 m CW/data 21.025-21.200 and phone 21.275-21.450. Extra opens up more at the bottom of each phone segment (for example 3.600, 7.125, 14.150, 21.200) and the bottom of the CW segments (3.500, 7.000, 14.000, 21.000). General also has all of 160 m, 30 m, 17 m, 12 m and 10 m, plus 60 m. 30 m is CW and data only, with a 200 W PEP limit and a requirement not to interfere with other services.

Technicians are limited on HF to CW on 80, 40 and 15 m (the same bottom-end segments as General), plus 10 m: CW/data 28.000-28.300 and SSB 28.300-28.500, at 200 W PEP. That means FM at 29.600 MHz is General and up. Technicians have all privileges above 50 MHz. Novice and Advanced licenses are no longer issued, but existing holders keep their privileges, so you'll still see those on older charts.

The common digital watering holes are conventions, not rules. FT8 dial frequencies are roughly 1.840, 3.573, 7.074, 10.136, 14.074, 18.100, 21.074, 24.915 and 28.074 MHz. Check the current plan for exact values, because FT4 and other modes sit nearby. CW tends to live in the bottom 50-100 kHz of each band, with the beacon sub-band on 10 m around 28.2 MHz. Many operators leave the top of the 80 m phone segment (about 3.790-3.800) as a DX window.

On band edges, remember that the rule applies to your occupied bandwidth, not your dial readout. In USB, your signal extends upward from the dial frequency, so at the top of 20 m (14.350) you want the dial a few kHz below it. In LSB the signal extends downward, so at a lower edge like 3.800 for a General on 80 m, dial a few kHz above it. Aim for at least roughly 3 kHz of margin, and more if your audio is wide or your rig calibration is questionable. Check your dial against a known reference now and then.

60 m is the odd one out. It is channelized, not a continuous band. The US channel center frequencies are 5332, 5348, 5358.5, 5373 and 5405 kHz. For USB the dial frequency is 1.5 kHz lower: 5330.5, 5346.5, 5357.0, 5371.5 and 5403.5. Privileges are General and above, power is limited to 100 W ERP referenced to a half-wave dipole, and the signal must stay within a 2.8 kHz channel. Allowed emissions are USB voice, CW and certain data modes. Other countries have allocated spectrum there differently, including a newer 5351.5-5366.5 kHz secondary allocation in many places. Verify the current US implementation before assuming you can use it.

  • Administrators

Picking up from HF, the VHF/UHF side is simpler in some ways because Technician and up all have full privileges there, but the plan matters more because so many people use FM, SSB, digital and repeaters on the same band.

6 m (50-54 MHz): the bottom 100 kHz (50.0-50.1) is CW only, and 50.060-50.080 is the beacon area. The DX window is around 50.100-50.130, and the usual SSB calling frequency is 50.125. FT8 is typically 50.313. FM simplex is typically 52.525, the national FM calling frequency, with repeaters in the 51-52 and 53-54 areas.

2 m (144-148 MHz): 144.000-144.100 is CW only and the weak-signal area runs up from there. 144.200 is the standard SSB calling frequency, and FT8 is commonly 144.174. The national FM simplex calling frequency is 146.520. APRS in North America is usually 144.390. Repeaters are spread through the band with the usual offsets (600 kHz is standard on much of 2 m, but your local coordinator decides), so check the local repeater directory before assuming.

70 cm (420-450 MHz): the national FM simplex calling frequency is 446.000, and the weak-signal CW/SSB calling frequency is 432.100. Repeaters commonly use a 5 MHz offset. Be aware of geographic and power restrictions here, because the amateur service is secondary on 70 cm. 97.303 has limits near certain radar installations and near the Canadian border. If you're near either, look up the footnotes.

33 cm (902-928 MHz): this band is shared with Part 15 devices and ISM equipment, so you may hear noise or find it crowded. Amateur use is secondary and some geographic restrictions exist, so check 97.303. Weak-signal calling is around 903.100. FM channel plans vary by region, so ask your local frequency coordinator rather than relying on a generic chart.

A simplex etiquette note that applies on every VHF/UHF band: use calling frequencies to make contact, then move off to another simplex frequency so you don't tie up the calling channel. The band plan, not the rules, drives this.

On the international question, the ITU divides the world into three regions. The US, Canada and Latin America are Region 2. Europe, Africa and the Middle East are Region 1. Asia and the Pacific are mostly Region 3. Allocations differ by region and by country, with a few examples. 40 m is 7.000-7.300 in Region 2, but only 7.000-7.200 in Region 1, where the 7.200-7.300 segment is used by broadcasters, so you may hear them. 80 m is 3.500-3.800 in Region 1 versus 3.500-4.000 in Region 2. 2 m is 144-146 in Region 1 and 144-148 in Regions 2 and 3. 70 cm is 430-440 in Region 1. 6 m is not available everywhere. IARU publishes regional band plans that differ from the ARRL plan, so DX operators often split (transmit and receive on different frequencies) to work around the differences.

If you're traveling, you're generally bound by the host country's rules, not your home license class. Look up reciprocal arrangements such as CEPT T/R 61-01 in Europe, IARP in parts of the Americas, or the host country's own procedure before you go.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.