Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Repeater basics checklist: offsets, tones, linking, and the etiquette that goes with them

ci_cover.jpg

Many newcomers to repeaters hit the same few problems. The radio hears the repeater but the repeater won't hear the radio. Or it works until someone says "this one is linked to something." Or the user keys up, gets a burst of noise, and has no idea why. This thread is meant to collect the practical details in one place, so add corrections and local variations.

Start with the five numbers on a listing. A repeater entry normally gives the output frequency (what you listen to), the offset direction and size (where you transmit relative to that output), the access tone (CTCSS/PL or DCS) your radio must send, sometimes a different tone the repeater sends back, and the mode. Offsets are set by regional band plans. In North America, 2 m is usually 600 kHz and 70 cm is usually 5 MHz, with the direction (plus or minus) depending on which part of the band the output sits in. Other regions use different 70 cm offsets, so check the local band plan rather than trusting a radio's auto-offset feature.

Tone terminology is a common source of confusion. "Tone" on many radios means your radio transmits a CTCSS tone but still opens its speaker on any signal. "Tone squelch" (TSQL) means it also requires that tone on received audio before it unmutes. DCS is a digital sub-audible code that serves the same purpose. Some radios let you set encode and decode separately, which matters when the repeater's input tone and output tone differ. Is it a habit in your area to list both tones, or just the input?

Last, a question for the group: what do you tell new hams about the difference between an open repeater and a closed one, and how do you tell from a directory entry which one you're looking at?

  • Replies 2
  • Views 24
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On open versus closed: an access tone does not by itself make a repeater closed. Many open repeaters require a tone on the input just to keep out noise and distant co-channel signals. A closed or limited-access repeater is one where the owner restricts use to members, to a particular group, or to people who have asked. A directory listing may say "open," "closed," or "private," and the data can be out of date. If a listing is vague, check the club's website or contact the trustee before assuming you're welcome.

On etiquette, a few habits cover most situations. Listen first, because the repeater may be in use, may be part of a net, or may be linked to a busy system. Pause a second or two before replying so others can break in, and keep each transmission short enough to stay well inside the time-out timer. A TOT is typically a minute or a few minutes, and exceeding it drops the repeater mid-sentence. Identify as your licence requires. In the US that means giving your callsign at least every 10 minutes and at the end of a communication. Rules differ elsewhere. "Kerchunking" (keying up just to see if you hit the repeater) is discouraged, so just say your callsign and that you're testing or monitoring. If you need to interrupt, "break" with your callsign is the usual way in, and an emergency or priority call takes precedence over normal chat.

Coordination is another thing worth knowing. In many regions a frequency coordinator or coordinating body assigns repeater pairs so that systems in the same area don't interfere with each other. Rules for what happens in a dispute vary by country. In the US, the operator of an uncoordinated repeater is generally expected to resolve interference with a coordinated one. A coordinated repeater is not automatically "better," but it usually has had its location, power and antenna height reviewed for interference.

  • Administrators

Here is the linking side. The important point is that "linked" can mean several different things, and each changes how you should operate.

EchoLink, IRLP and AllStarLink are all voice-over-IP systems tied to analog FM repeaters or simplex nodes. EchoLink requires callsign validation and uses node numbers and conference servers. IRLP uses node numbers and reflectors, and commands are sent by DTMF. AllStarLink is built on Asterisk, uses node numbers, and lets one node connect to others or to hubs, again controlled by DTMF. Wires-X is Yaesu's system for System Fusion (C4FM) and uses a gateway node connected to "rooms." Each of these has its own control codes, and the owner may restrict who can connect or disconnect. Don't send commands unless you know the local rules, and ask on the air before dropping a link that someone else may be using.

Linked systems have more delay than a standalone repeater, and the audio may be going to many places at once. Leave a longer gap between overs, avoid private side conversations over a wide-area link, and say clearly if you want a local-only QSO. Some repeaters announce the link status or have a courtesy tone that changes when a link is up. If you don't know what a given repeater does, listen for a few minutes.

DMR and D-STAR repeaters work differently from analog FM. DMR uses two time slots on each 12.5 kHz channel, a color code that must match, talkgroups to select who hears you, and a DMR ID registered to your callsign. D-STAR uses callsign routing, with fields such as MYCALL, URCALL and RPT1/RPT2, and reflectors identified by a prefix, number and module letter. Because these need correct codeplug or radio settings, a sub-audible CTCSS tone is not the key detail on those systems. Whether a talkgroup is static or dynamic affects how much traffic lands on a repeater, so read the owner's notes before you start talking on an unfamiliar one.

For finding repeaters, use more than one directory. RepeaterBook and printed or online band-plan listings are common starting points, and the club's own page is usually the most current source. For digital systems, check the network's own lists and the repeater's page for color codes, talkgroups, reflectors and rooms. Joining the club that maintains a repeater is a good way to learn its rules and help keep the system on the air.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.