Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a 5 W portable QRP setup: rig choice, antenna, and power. Where does the efficiency actually come from?

ci_cover.jpg

QRP threads tend to turn into rig comparisons, but the rig is usually the smallest variable in how many contacts you make. I'd like to collect practical thinking on the whole chain: radio, antenna, feedline, battery and operating habits. The goal is a field kit that works at 5 W on CW or a few watts on SSB without becoming a pile of compromises.

Definitions. The usual QRP convention is 5 W output or less on CW. For SSB, 10 W PEP is often quoted, and QRP-ARCI contests use their own power categories. Check the current rules for any event you enter, because categories and multipliers for lower power can change from one contest to the next.

Rig categories. Roughly, the options fall into three groups:

  • Full-featured portables such as the Elecraft KX2 and KX3. They cover multiple bands and modes, including SSB, CW and digital, with built-in tuners as an option. They cost more and have more menus, but they are flexible if you want one radio for everything from SOTA to a hotel-room setup.
  • Compact CW-focused kits such as the Mountain Topper line (the MTR series) and the Penntek TR-35. These are small, light and low on current draw, and they suit a stripped-down CW activation. The trade-off is fewer features and, for some, a fixed band or limited band set. Check the manual for the exact bands, voltage range and output power.
  • Minimalist and learning kits such as the Pixie and other Hendricks-style designs. The Pixie is a very simple CW transceiver, and its output is typically a fraction of a watt to a watt or so. It is a great introduction to how a transmitter, receiver and sidetone chain work. As a daily driver the receiver is the weak point, since selectivity and sensitivity are modest. It is still a good bench project, and it can make real contacts when conditions cooperate.

Calling frequencies. QRP operators commonly gather around these, though regional band plans and local activity vary:

  • CW: 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906, 28.060 MHz
  • SSB: 3.985, 7.285, 14.285, 21.385, 28.885 MHz

Treat them as meeting points. Call CQ there, but be ready to move up or down a few kHz if it is busy. Also check your own band plan, because 7.030 and other segments sit differently depending on region.

Antennas. At 5 W you cannot buy back a bad antenna with power. A few common choices:

  • A resonant dipole or inverted V on coax is simple, predictable and efficient when it is cut properly.
  • An end-fed half wave (EFHW) with a matching transformer is popular for portable use because it needs only one high support, but the transformer, the counterpoise and the coax run all affect efficiency.
  • A vertical with a few radials, or a random wire with a tuner and counterpoise, is workable for quick setups, but results depend heavily on ground and radial layout.

Height and clear surroundings matter at least as much as the antenna type. For feedline, use light low-loss coax and keep it short on the higher bands. Losses from long runs of thin coax at 28 MHz can quietly eat a real fraction of 5 W.

Power. LiFePO4 packs are attractive: light, stable, and flat across most of the discharge. A 4S pack is nominally 12.8 V but can sit around 14.4 to 14.6 V when fully charged. Before you plug it in, check your radio's maximum supply voltage. Some QRP rigs are specified for a narrower range than a 4S LiFePO4 pack will deliver. Also check connector polarity, add an inline fuse, and consider how the radio behaves as the pack nears empty. Output power on many rigs depends on supply voltage, so the number on the spec sheet may not match what you get from a partly discharged pack.

Operating efficiency. Moving from 5 W to 50 W is only about 10 dB, a bit under two S-units on a typical S-meter scale. A good antenna, a clear band opening, a quiet location and a short, well-timed CQ can be worth more than that. On CW, a narrow filter and good sending speed help a lot. On SSB, tight audio and a clear speech processor setup help more than turning the mic gain up.

So what is everyone building or carrying, and which part of the chain have you found most worth the effort?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The antenna point is the one that gets overlooked most. Many people spend serious money on a radio and then hang a short wire six feet off the ground. A rough way to think about it: 3 dB of antenna or feedline improvement is the same as doubling your power, and at 5 W doubling is a bigger practical step than it sounds.

On EFHWs, keep the matching unit's limits in mind. A transformer rated for QRP power is fine at 5 W, but the quality of the core and winding affects loss, and the coax shield will often act as part of the antenna unless you add a choke or a counterpoise. If you see SWR change when you move the coax, that is usually a sign the feedline is part of the radiating system. It is not necessarily a fault, but it does change patterns and noise pickup.

For the rig, I'd pick by how you plan to operate. If you only want CW on a hill, a small dedicated CW rig keeps the weight and current draw low. If you also want SSB or digital, a KX2 or KX3 gives you a lot more flexibility, at the cost of price and a steeper learning curve. A Pixie is a fun build, but it makes sense to treat it as a project and not as your only field radio.

  • Moderators

On batteries, the main thing I would add is to measure rather than assume. A small inline voltmeter or a rig with a voltage display shows you how the pack behaves under transmit load. Some rigs sag or reduce power when the supply voltage drops, and some have a low-voltage cutoff that surprises you in the middle of a QSO.

For LiFePO4, a proper BMS (battery management system) or protected pack is worth having, and so is a charger meant for that chemistry. Keep the wiring tidy: fused positive lead, decent connectors (Powerpole is common), and a short cable to the radio. If your rig has a stated upper voltage limit, check it against the full-charge voltage of the pack, not just the nominal figure on the label.

For QRP-ARCI events, it is also worth reading the exchange and power rules before you go out, so you know whether to log power class or other details. Contesting at low power rewards patience and a good listening ear: find a clear spot, call a few times, and move on if nobody comes back. Working the stations calling CQ often gets you contacts faster than waiting for answers to your own call.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.