Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Gain staging and dynamic range on budget SDRs: why ghost signals appear and how to track them down

ci_cover.jpg

A common complaint with RTL-SDR dongles, HackRF, SDRplay RSP units and Airspy receivers is a waterfall full of signals that don't belong: FM broadcast images in the aircraft band, a carpet of spurs across 40 m, or a strong local pager that seems to appear on a dozen frequencies. Usually the receiver isn't broken. The front end or ADC is being driven past its comfortable range, and the software shows exactly what it's given.

The basic issue is dynamic range. An RTL-SDR (RTL2832U with an R820T2-type tuner) has an 8-bit ADC. HackRF One is also 8-bit but covers 1 MHz to 6 GHz with up to 20 MHz of bandwidth. SDRplay's RSP1A and RSPdx use 14-bit converters, and the Airspy R2 is 12-bit. Each ADC bit is worth roughly 6 dB in theory, but real-world performance is lower because of tuner noise, filtering, and the whole analog chain ahead of the converter. More bits help, but front-end selectivity, preselection filters and sensible gain settings matter just as much.

A quick test for overload: while watching a suspicious signal, reduce RF gain or add a fixed attenuator (3 to 10 dB) at the antenna input. A real signal drops by the amount you attenuated. Intermodulation products and images usually fall faster. Third-order products change roughly 2 dB for every 1 dB of input change, so they collapse when you back off. If the ghost disappears or drops sharply, you have an overload problem and not a propagation mystery.

On the software side, the tools behave differently. SDR# and SDRuno (SDRplay's own Windows application) give you direct control of tuner gain stages, and SDRuno exposes the RSP's gain reduction and notch filters. GQRX on Linux and macOS goes through the osmosdr or SoapySDR layer, so which gain sliders you see depends on the driver. HDSDR relies on ExtIO plugins, and CubicSDR uses SoapySDR, which makes it flexible with LimeSDR and others. Whatever you use, AGC in the SDR front end often hides the problem, so try manual gain for diagnosis. On HackRF, set the RF amp (14 dB) off unless you really need it, then balance the LNA (IF) gain in 8 dB steps and the baseband VGA gain in 2 dB steps. Raising the baseband gain too much just amplifies noise without improving sensitivity.

Antennas and filtering contribute as much as the radio. A wideband antenna such as a discone feeds every strong broadcast station to the front end at once. For VHF/UHF work, a tuned dipole, or a simple broadcast FM notch filter in front of an RTL-SDR, can clean up the display. The RSP1A and some other models have built-in broadcast notch filters. For ADS-B at 1090 MHz, a band-pass filter plus an LNA located close to the antenna is the usual approach, because mounting the LNA after a lossy coax run adds the cable loss directly to your noise figure. For HF, RTL dongles need direct sampling mode (on some units) or an upconverter that shifts HF into the tuner range. Direct sampling is limited by the same 8-bit ADC, so expect compromises. Upconverters work, but oscillator spurs and a poor filter chain can introduce their own images.

Local noise is a separate problem. USB 3.0 ports, switching power supplies, LED lighting and the computer itself can radiate across HF and VHF. Try a USB extension cable to move the dongle away from the computer, add ferrite chokes on the USB and coax, and use a powered hub if the port is noisy. Comparing the noise floor with the antenna disconnected (and a 50 ohm terminator fitted) against the antenna connected tells you quickly whether the noise is internal or arriving from outside.

Some questions for discussion: which receiver, antenna and software combination are you running, and how do you set gain? Do you use a bandscope or panadapter feed from a transceiver, or a standalone SDR? And for decoding (DMR with DSD, POCSAG with multimon-ng, ADS-B with dump1090, WSJT-X modes through a virtual audio cable), have you found that errors come mostly from low signal level, overload or sample rate/audio routing problems?

  • Replies 2
  • Views 59
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Good starting point. One thing I'd add is to check the displayed noise floor when you change gain, not just the signals. If turning gain up raises the noise floor by the same amount as the signal you want, you gain nothing, and you just move closer to ADC clipping. The aim is for the antenna's external noise to lift the floor a few dB above the receiver's own noise, and no more. On a quiet VHF band that usually means a higher gain setting than on HF, where atmospheric and man-made noise are already strong.

The attenuator test is also worth doing with a known-clean signal. If a strong FM station is the cause, a notch filter at the antenna will make the ghosts disappear, and software tweaks won't. Filters belong before the first active stage; a filter after the LNA can't undo the overload that already happened in the LNA.

For HF with an upconverter, check the converter's local oscillator frequency and remember that your SDR software will show frequencies offset by that amount unless you set the offset in the program. SDR#, HDSDR and others each have their own way to configure it, so verify with a known station such as a time signal or a broadcast carrier before trusting the dial.

  • Administrators

Regarding decoding, I'd separate the failure modes. If a decoder isn't producing output, first check that the signal is strong and stable in the waterfall with enough bandwidth selected. For narrowband digital modes like POCSAG or DMR, a very wide filter lets in noise and neighbours, so narrow it to the channel width. For WSJT-X modes, the audio path through a virtual cable is the usual weak point: sample rate mismatches, the wrong audio device, or an audio level that's clipping. WSJT-X's level meter wants a moderate value and not a pegged one. Also make sure the PC clock is accurate, because FT8 and similar modes depend on timing within about a second.

On panadapters, there are two broad approaches. One is a dedicated SDR on the radio's IF output, which gives a bandscope view of the band around your transceiver's frequency. The other is a second antenna or a split from the main antenna feeding the SDR. If you split from the main antenna, use a proper splitter or a protection arrangement, because transmitting into an SDR input can destroy it. Even a simple relay arrangement needs care. An SDR input is not designed to survive transmit power, and that applies to RTL-SDR, Airspy, RSP and HackRF alike.

If you're using a LimeSDR or HackRF as a receiver only, remember that they are transceivers with sensitive RF paths too. The bias tee, if enabled for an active antenna or LNA, supplies DC on the coax, so don't connect it to a DC-grounded antenna or any device that shorts the center conductor.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.