Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio setup: mic gain, ALC, compression and bandwidth for clean signals that carry on weak-signal and DX paths

ci_cover.jpg

Many SSB audio problems come from one habit: turning things up until the meter looks busy. A clean SSB signal is usually a matter of gain staging, sensible filtering and checking what you actually put on the air. Here is a framework to critique or add to.

1. Start with the microphone and its position. Mic choice matters less than consistency. Whatever you use (a headset, a desk mic or the stock hand mic), keep a fixed distance, typically a few centimetres from the lips and slightly off-axis to reduce plosives and breath noise. If your level changes whenever you lean back, the compressor and ALC end up fixing a problem that technique should have solved. A foam windscreen helps, and so does keeping the mic away from the shack fan and the PC speakers.

2. Set mic gain by the ALC, not by feel. Check your rig's manual, because ALC meters differ. The usual approach is to speak at normal volume with the processor off and raise mic gain until the ALC just starts to move on voice peaks, then back off a little. ALC should stay within its recommended zone and not pin at the end of the scale. Heavy ALC action means you are flattening peaks in a crude way, which adds distortion and widens the signal. If you run an external amplifier, also watch the amp's ALC line. Over-driving the exciter or the amp is a common source of splatter.

3. Use the speech processor for a purpose. Compression raises average power relative to peak power, which can help a weak signal stay readable through noise and fading. But more is not better. A small amount of compression, often described as a few dB on the rig's compression meter, is usually where the gain is. Beyond that you mostly raise background noise, emphasise sibilance and room echo, and increase distortion products. RF-clipping types and AF compressors behave differently, so read how your radio implements it. If a station tells you that you sound harsh or pumpy, turn the processor down before touching anything else.

4. Shape the audio with the equalizer or TX bandwidth settings. Most communications audio is carried between roughly 300 Hz and 2.7 kHz. Low frequencies below about 200 Hz cost transmit power and add little to readability. A gentle boost in the 2 to 3 kHz region often improves intelligibility more than a boost in the bass. Make small changes, then listen to a recording. Many rigs let you narrow or widen the TX bandwidth. A standard setting around 2.4 to 2.7 kHz is a good starting point. A wider setting can sound pleasant on a quiet band during a casual chat, but it occupies more spectrum, so be considerate when the band is crowded or in a contest.

5. Use the monitor, but do not trust it blindly. The TX monitor lets you hear the processed audio in headphones. It is excellent for spotting hum, RF feedback, clipping and over-compression, but it generally reflects the audio stage and not the final RF signal. For a true check, listen on a second receiver, use an SDR or a remote receiver to see the occupied bandwidth, and ask for an honest report from someone with a quiet receive location. Record yourself where possible and compare the result with what you expect.

6. Remember the sideband convention. By convention, amateurs use LSB on 160, 80 and 40 metres, and USB on 20 metres and above. On 60 metres, USB is the norm. It's a convention, not a technical necessity, and the main point is that both stations need to be on the same sideband to understand each other. Use the clarifier or RIT sparingly to correct for slight frequency offsets, and keep the TX frequency stable.

7. Working weak stations. On receive, use a filter close to the width of the signal: the standard 2.4 kHz filter is a good default, and many operators narrow it a little more when there is interference or noise. Keep AGC in a sensible setting, reduce RF gain or switch the preamp off when strong adjacent signals or local noise push the receiver, and use noise reduction in moderation, because heavy DSP can make speech sound artificial and hide the very detail you need. On transmit, speak clearly and not faster. Use standard phonetics for callsigns and signal reports, and repeat key information once rather than endlessly.

8. DX and pileups. Listen before calling. Work out whether the DX station is working split, which stations it is answering and where, and set your TX frequency accordingly. A clean signal with moderate compression generally does better than a loud, distorted one, because it is easier to copy and does not splatter over other callers. Keep the call short, send it once or twice, and then listen. If the DX station is struggling, repeating your callsign clearly and with good timing is more effective than adding processing.

What mic gain/ALC/processor combination do others use as a baseline for general operating, and when do you change it for contests or DX?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One thing worth adding is that ALC behaviour varies between radios, so "ALC just flickering" is not a universal rule. Some rigs show it as a bar graph, some have a defined acceptable zone, and some work differently when the processor is on. Check the manual for your model, then verify with an independent receiver or SDR. A meter reading alone does not tell you whether the signal is clean.

For the processor, a useful test is to record a minute of normal talking with it off, then with a low setting, then a high setting. Play them back at the same volume. The high setting may sound louder, but you will often hear more noise, breath and room reflections. That is a good reminder of what the person at the other end gets when the band is already noisy.

  • Moderators

On bandwidth, I would separate casual ragchewing from DX and contest operating. A wider TX setting can make voices sound more natural on a quiet band when you are not crowding anyone, but in a pileup or contest it makes sense to keep the occupied bandwidth tight, around 2.4 kHz or a bit more. It reduces interference to neighbours, and narrow audio puts more of the power into the part of the spectrum that carries intelligibility.

Also check your PC or digital audio chain if you use a USB interface. Settings in the operating system, a voice-processing app or the rig's own menu can stack on top of each other, giving you double compression or low-cut filters you did not intend. Reset everything to a flat, known setting first, then add processing one step at a time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.