Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting started with LEO satellites: FM birds first, then linear transponders, and where Doppler and tracking fit in

ci_cover.jpg

This thread is for sorting out the practical path from "I have a dual-band HT" to working SSB and CW through a linear transponder. Satellite operating looks like one big skill, but it is really several smaller ones: predicting passes, pointing an antenna, correcting for Doppler, and using the right etiquette for the type of bird. Please correct anything I get wrong.

Start with FM birds. FM satellites such as AO-91, AO-92 and SO-50 have worked as single-channel repeaters: one uplink frequency, one downlink frequency, and anyone who can get into the bird shares the channel. Many need a CTCSS tone on the uplink, and SO-50 has historically needed a specific arming tone sequence. Frequencies, tones and operating status change, so check the current AMSAT status pages and your tracking software's frequency file before you plan a pass. Do not rely on a number you remember from an old forum post. The ISS is a similar case: it has carried both an APRS digipeater on 145.825 MHz and a cross-band voice repeater, but what is switched on varies with crew schedules and onboard equipment.

Why FM satellites feel hard. The satellite is moving quickly, so you hear it on the downlink at a frequency that slides during the pass. At 145 MHz the shift is a few kHz either side of nominal, and at 435 MHz it is roughly three times larger, around the 10 kHz range at the extremes. FM receivers tolerate a few kHz, but if you ignore the shift entirely the signal gets noisy and weak near the start and end of a pass. A common routine is to keep the downlink stepping in 5 kHz or 2.5 kHz increments, and to adjust the uplink opposite the Doppler direction on the transmit side. Software can do this for you through CAT control, but doing it by hand a few times teaches you what is actually happening.

Tracking software. Gpredict is a free cross-platform tracker that gives you pass tables, a polar plot, a map view and optional rig and rotator control through Hamlib. SatPC32 is a Windows program popular for Doppler control with many radios, and it uses a frequency file and Keplerian elements that you must keep updated. Whatever you use, set your location by grid square or lat/long, confirm your computer clock is accurate, and refresh the TLEs or Keps regularly. Old elements are the most common reason a predicted pass is minutes off.

Antennas. For handheld work, an Arrow-style dual-band Yagi (or a similar handheld 2 m/70 cm Yagi) is the usual starting point. You hold it, point it at the satellite by eye or with a phone app, and use either two radios or a duplex-capable radio. Pointing and polarization matter more than power. Remember the elevation as well as the azimuth, since a high pass can move through the sky quickly. For fixed stations, a pair of crossed Yagis on an az/el rotator lets the controller follow the satellite, but you do not need a rotator to be effective on FM. Circular polarization helps with fading from satellite spin, but it also costs gain, so treat it as an upgrade, not a requirement.

Linear birds. RS-44 is a good example of a linear transponder that people use for SSB and CW. A linear transponder takes a slice of spectrum, flips or translates it, and retransmits the whole slice, so many stations can be heard in the passband at once. Many of these transponders are inverting, so the sideband and the tuning direction reverse between uplink and downlink. Your downlink frequency is the one to treat as the anchor: after you set your uplink, you listen to yourself on the downlink and adjust until your own signal sounds right. Use low power, because a strong uplink signal can desensitize the transponder and push everyone else down. If you can hear yourself clearly at low power, it is usually enough.

Contacts and exchanges. A typical contact is brief: callsign and four-character grid square, such as FN31, sometimes a signal report. Grid squares are part of the culture because rovers and DXpeditions activate rare grids, and awards like VUCC are based on them. On a busy pass, keep exchanges short and give your callsign clearly.

Geostationary alternative. QO-100 (Es'hail-2) is different from the LEO satellites: it is geostationary, so there is no Doppler to correct and no pass to chase. The uplink is on 2.4 GHz and the downlink on 10 GHz, so the challenge is the station build, with a dish, a suitable feed, an LNB with stable frequency control, and enough uplink power and polarization alignment. It is only usable from within its coverage footprint.

Questions for the thread: what was the first thing that helped you get past your first FM satellite pass, and what do you recommend for someone who wants to move to RS-44 without buying a rotator setup immediately?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One practical tip for FM passes is to prepare the radio before AOS, not during it. Program memories for the satellite you plan to work, with the uplink tone set and the downlink in a separate memory or VFO. Write the pass times, maximum elevation and direction on a card. If the pass is under about 15 degrees maximum elevation, treat it as a bonus rather than a main target, because the path is long and horizon obstructions will hurt you. Also remember that you cannot hear another station while transmitting on a half-duplex radio, so listen first, find the gap, and keep your over short, just your call and grid. If you can use a second receiver or a duplex radio, you can hear your own downlink and spot problems with your Doppler correction.

  • Administrators

For linear birds, I would add a note about CW and SSB differences. CW is usually the easier way to learn, because the tone you hear on the downlink gives you immediate feedback about frequency offset, and a weak CW signal can be copied when SSB would not be readable. For SSB on an inverting transponder, don't assume your rig is automatically set to the right sideband. Check your software's transponder definition, and tune by listening to your own signal in the downlink. Doppler matters even more here, because you need your signal to stay in the same part of the passband while the satellite moves. A simple approach is to let software correct the downlink while you make only small uplink changes, or the reverse, so you do not chase yourself up and down the band. Finally, check your TLE age before blaming your antenna or radio, because stale elements and a wrong clock can look exactly like a weak signal.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.