Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig triage: what do you check first for no TX, no RX, or SWR protection faults?

ci_cover.jpg

This thread is about a repeatable order of checks for a rig that is dead, deaf, or won't transmit. The aim is to find which stage has failed before any parts get replaced. Add your own methods below.

A sensible order is: power, control and clocks, signal path, then alignment. The common mistake is to start at the end, tweaking slugs or trimmers on a rig whose real problem is a sagging supply rail.

Start with power. Check the fuse, the DC plug and connector, and the polarity protection. Then measure the voltage at the rig's input terminals with the rig drawing current. An open-circuit reading on a tired supply or a corroded connector can look fine and collapse as soon as the PA draws current. A bench supply with an adjustable current limit helps here, because you can see the current draw and limit the damage if something is shorted.

Next, check the internal rails. Look at the regulators, the 5 V and 3.3 V logic supplies, the switched TX and RX rails, and the reference voltages. If the display is dead or the micro is resetting, nothing else will behave. For a PLL, check the reference oscillator with a counter or scope and see whether the lock-detect line looks sane. An unlocked synthesizer can cause both no TX and no RX.

Then separate the symptoms. If TX and RX are both dead but the rig powers up, suspect the common parts: the synthesizer or VCO, the reference oscillator, the antenna relay or PIN diode switching, the band switching logic, or a shared supply rail. If only one direction fails, you have a much shorter signal path to trace.

On SWR protection: many rigs fold back power when the sensing circuit sees high reflected power. That does not always mean the antenna is bad. Test into a known-good dummy load first. If protection still trips, suspect the forward/reflected detector diodes, the bridge balance, bad bypass or coupling capacitors in the sensor, the low-pass filter relays, or the connector and jumper at the antenna jack. If it is fine on a dummy load but not on the antenna, the fault is outside the rig.

For blown finals, the failed transistors are often a symptom. Before fitting new devices, look for what killed them: a high-SWR event, excessive drive, a parasitic oscillation, a failed bias circuit, a supply overvoltage, or bad thermal contact. Check the driver stage, the bias network and any thermal compensation parts, and replace the devices only with the correct type. Set the idle current per the manual with a current meter in line, starting low and working up.

For capacitors, aging electrolytics in power supplies and audio stages are the usual suspects. Match the capacitance and voltage rating, and use a sensible temperature rating. Be more careful with RF-critical capacitors such as NP0/C0G, mica, and trimmers. Replacing those blindly can shift the tuning. An ESR meter is useful for electrolytics, and a plain capacitance reading can miss a part that is failing under load.

What order do you work in, and what test gear do you reach for first?

  • Replies 2
  • Views 34
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One thing worth adding to the power check is voltage drop. Measure from the supply terminals to the rig's input terminals while transmitting. Even a few tenths of a volt lost in a cigarette-lighter plug, a thin lead, or a worn Anderson-style contact can make a rig misbehave on transmit. Low voltage can cause low output, distortion, a resetting micro, or protection circuits tripping. It can look like a rig fault when the real problem is in the cable.

For no-receive faults, I'd go stage by stage from the antenna jack toward the speaker, and the service manual's block diagram is the map for that. A signal generator at a known level into the antenna port, with a scope or an audio meter on the speaker output, lets you work out roughly where the signal disappears. If the manual has test points or expected voltages, use them. A DMM covers the DC side: supply rails, bias voltages, AGC or mute lines, and relay drive. A stuck mute or squelch line can look like a dead receiver.

For cleaning contacts, use contact cleaner sparingly on switches and pots, and avoid soaking nearby plastics or trimmers. Isopropyl alcohol works for flux residue and dirt on boards. If a fault changes when you tap the board or wiggle a connector, look at connectors, ribbon cables, and cracked solder joints before touching any components.

  • Administrators

On the scope side, the main limitation is bandwidth and probing. A scope is great for checking an oscillator, a clock, a keying line, audio, or the RF envelope on transmit. For HF rigs, a 10x probe with a short ground spring is much better than a long clip lead, which adds inductance and can distort what you see. Measuring RF directly in a PA stage can also load or detune the circuit, so use light probing, a proper RF probe, or a pickup loop. And never measure on a PA stage without a dummy load connected.

For SWR faults and suspected oscillation, a dummy load, a wattmeter, and a spectrum view or a nearby receiver help you separate a real fault from a sensing problem. If the output is wrong at one band only, check that band's LPF relay and filter components. If it is wrong everywhere, look at the common path and the drive level.

On alignment: leave it until the rig is otherwise healthy. Fix supply, bias, synthesizer lock, and gross faults first. Then follow the service manual's procedure and use the specified test equipment. Mark the original slug or trimmer positions if you must move them. A frequency counter for the reference oscillator, an RF millivoltmeter or a signal generator for receive, and a power meter for transmit cover most of it. If the manual says a specific adjustment needs a specific tool or level, take that seriously, because the wrong approach can leave you with a rig that looks aligned and performs poorly.

With AC-powered or tube gear, the safety rules are stricter. Discharge the high-voltage capacitors, use an isolation transformer where appropriate, and take care with switch-mode supplies. A series lamp limiter is a classic way to limit current on a first power-up of old mains gear.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.